Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.01–2012.04
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU (brake actuator assembly).

·

The anti-lock brake system is defective.


WIRING DIAGRAM

C241516
3.073,2.396 4.063,2.573 0.99,0.177 10 from IG Circuit 5.604,0.792 5.969,0.948 0.365,0.156 10 WA 5.594,1.094 6.042,1.25 0.448,0.156 10 GND1 5.594,1.521 6.042,1.677 0.448,0.156 10 GND2 5.594,1.906 6.042,2.063 0.448,0.156 10 IG1 5.594,2.396 6.042,2.552 0.448,0.156 10 EXI2 5.281,0.688 5.458,0.833 0.177,0.146 10 13 5.354,0.979 5.479,1.125 0.125,0.146 10 2 5.281,1.396 5.458,1.542 0.177,0.146 10 24 5.281,1.781 5.458,1.927 0.177,0.146 10 25 5.281,2.271 5.458,2.417 0.177,0.146 10 22 2.854,0.667 3.885,0.917 1.031,0.25 10 Reverse Circuit 2.427,0.958 2.76,1.125 0.333,0.167 10 ABS 4.427,0.688 4.667,0.865 0.24,0.177 10 38 1.771,0.677 1.969,0.844 0.198,0.167 10 21 2.271,1.375 2.74,1.542 0.469,0.167 10 G19 2.271,1.542 4.146,1.76 1.875,0.219 10 Combination Meter Assembly 0.469,0.792 1.458,0.969 0.99,0.177 10 from IG Circuit 2.219,2.063 3.365,2.25 1.146,0.188 10 ECU-IG&GAUGE 0.604,1.906 1.594,2.083 0.99,0.177 10 from IG Circuit 5.344,2.781 5.813,2.948 0.469,0.167 10 A13 5.344,2.948 6.958,3.313 1.615,0.365 10 Skid Control ECU (Brake Actuator Assembly) 2.042,0.656 2.302,0.823 0.26,0.167 10 IG+ 4.115,0.688 4.375,0.865 0.26,0.177 10 LP

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK FOR DTC
a.

Check if DTCs for the ABS are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC not output A
DTC output B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C117862
1.542,0.646 1.885,0.875 0.344,0.229 1.458,2.854 1.375,2.854 1.375,2.854 1.313,2.229 false 0.073,0.042 0.385,0.198 0.313,0.156 10 *a 1.594,0.688 2.073,0.979 0.479,0.292 10 A13 1.51,2.771 1.99,3.063 0.479,0.292 10 IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-25 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.
C117862
1.521,0.646 1.875,0.896 0.354,0.25 1.656,2.771 1.469,2.771 1.469,2.771 1.073,2.156 false 0.667,1.083 0.792,1.083 0.792,1.083 1.052,1.865 false 0.083,0.073 0.396,0.229 0.313,0.156 10 *a 1.583,0.698 2.094,1.042 0.51,0.344 10 A13 0.26,1 0.771,1.344 0.51,0.344 10 GND1 1.698,2.688 2.208,3.031 0.51,0.344 10 GND2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 (GND1) - Body ground Always Below 1 Ω
A13-24 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G19 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-13 (WA) - G19-38 (LP) Always Below 1 Ω
A13-13 (WA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (EXI2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (EXI2 TERMINAL)
a.
C117862
0.104,0.051 0.372,0.262 0.267,0.212 10 *a 1.502,0.57 1.892,0.814 0.39,0.244 1.548,0.608 1.84,0.792 0.292,0.184 10 A13 2.042,2.892 2.4,3.062 0.358,0.17 10 EXI2 2.637,2.03 2.606,2.964 2.606,2.964 2.463,2.964 false
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-22 (EXI2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK ABS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK ABS WARNING LIGHT
a.
C117862
1.531,0.594 1.865,0.813 0.333,0.219 1.375,1.979 2.417,0.896 2.417,0.896 2.563,0.896 false 1.073,1.833 1.063,0.844 1.063,0.844 0.906,0.844 false 1.063,2.146 1.063,2.875 1.063,2.875 1.323,2.875 false 0.104,0.073 0.417,0.229 0.313,0.156 10 *a 1.573,0.625 2.063,0.938 0.49,0.313 10 A13 0.51,0.76 1,1.073 0.49,0.313 10 GND1 2.604,0.813 3.094,1.125 0.49,0.313 10 WA 1.365,2.781 1.854,3.094 0.49,0.313 10 GND2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Using SST, connect terminals 13 (WA) and 2 (GND1) or 24 (GND2) of the skid control ECU (brake actuator assembly) connector.


SST
09843-18040  

d.

Turn the ignition switch to ON.


e.

Check the ABS warning light.

OK:

ABS warning light turns off.



Result:
Proceed to
OK
NG



OK

NG

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)