Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.04–2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1282  Center Differential Lock Position Switch  


DESCRIPTION

DTC C1282 is stored only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1282 Center Differential Lock Position Switch Stored during Test Mode.
·

Harness or connector

·

Transfer system

·

Skid control ECU (Brake actuator assembly)



*C1282: for 4WD

WIRING DIAGRAM

C237097
5.333,2.24 5.688,2.417 0.354,0.177 10 false A36 5.333,2.406 6.885,2.792 1.552,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 5.448,1.188 5.708,1.344 0.26,0.156 10 false EXI 5.177,1.188 5.396,1.344 0.219,0.156 10 false 20 3.25,2.135 3.656,2.302 0.406,0.167 10 false C31 3.25,2.313 5.083,2.865 1.833,0.552 10 false 4WD Detection Switch (Differential Vacuum Actuator Assembly) 2.521,2.063 2.833,2.219 0.313,0.156 10 false ADD 2.927,1.802 3.042,1.948 0.115,0.146 10 false 3 2.51,2.469 2.865,2.625 0.354,0.156 10 false GND 2.938,2.667 3.083,2.844 0.146,0.177 10 false 4 0.25,5.104 0.542,5.271 0.292,0.167 10 false C37 0.25,5.281 2.219,5.458 1.969,0.177 10 false 4 Wheel Drive Control ECU 1.417,3.885 1.635,4.042 0.219,0.156 10 false DL 1.823,3.885 1.958,4.031 0.135,0.146 10 false 6 3.083,4.375 3.427,4.531 0.344,0.156 10 false C28 3.083,4.563 5.052,4.906 1.969,0.344 10 false 4WD Position Switch (No. 3 Transfer Indicator Switch) 2.99,3.885 3.115,4.031 0.125,0.146 10 false 2 4.26,3.875 4.385,4.042 0.125,0.167 10 false 1 1.344,1.198 1.719,1.385 0.375,0.188 10 false ADD 1.823,1.167 2.01,1.365 0.188,0.198 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (EXI TERMINAL)
a.

Connect the skid control ECU (brake actuator assembly) connector.


b.

Set the vehicle to the 4WD state using the transfer shift lever.


c.
C199357
0.208,1 0.542,1.229 0.333,0.229 2.177,1.896 2.094,1.896 2.094,1.896 1.958,1.25 false 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 0.26,1.042 0.698,1.365 0.438,0.323 10 false A36 2.219,1.813 2.542,2.021 0.323,0.208 10 false EXI
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-20 (EXI) - Body ground
·

Ignition switch ON

·

Transfer shift position H4


Below 1.5 V



e.

Connect the skid control ECU (brake actuator assembly) connector.


f.

Set the vehicle to the 2WD state using the transfer shift lever.


g.

Disconnect the skid control ECU (brake actuator assembly) connector.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-20 (EXI) - Body ground
·

Ignition switch ON

·

Transfer shift position H2


11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TEST MODE DTC

NG

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU AND 4WD DETECTION SWITCH)
2.CHECK TEST MODE DTC
a.

Switch the vehicle to Test Mode, check the H2 to H4 shift operation, and then check that DTC C1282 is cleared.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
Result:
Result Proceed to
Test Mode DTC is not cleared A
Test Mode DTC is cleared B




A

B

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU AND 4WD DETECTION SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the 4WD detection switch (differential vacuum actuator assembly) connector.


d.

Disconnect the 4 wheel drive control ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-20 (EXI) - C31-3 (ADD) Always Below 1 Ω
A36-20 (EXI) - C37-8 (ADD) Always Below 1 Ω
A36-20 (EXI) - Body ground Always 10 kΩ or higher
C31-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR