Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.01–2012.04
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1421  Open or Short in Master Cylinder Pressure Sensor  C1281  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

C106656
4.225,0.25 5.873,0.446 1.648,0.196 10 Brake Actuator Assembly 2.884,1.033 4.072,1.259 1.188,0.226 10 Skid Control ECU 5.389,2.42 6.542,2.827 1.153,0.406 10 Master Cylinder Pressure Sensor 0.466,1.874 1.342,2.128 0.876,0.253 10 from Battery 0.34,2.526 1.393,2.923 1.052,0.397 10 from Stop Light Switch 0.309,3.303 1.35,3.529 1.041,0.226 10 to Body Ground 2.758,1.93 3.192,2.131 0.434,0.201 10 IG1 2.758,2.603 3.208,2.814 0.451,0.212 10 STP 2.758,3.289 3.275,3.49 0.517,0.201 10 GND 3.794,1.93 4.268,2.142 0.473,0.212 10 VCM 3.822,2.603 4.273,2.814 0.451,0.212 10 PMC 3.92,3.289 4.238,3.504 0.317,0.215 10 E2 0.539,4.354 4.901,4.566 4.362,0.212 10 VCM: Power Supply for Master Cylinder Pressure Sensor 0.539,4.746 3.968,4.953 3.428,0.207 10 PMC: Master Cylinder Pressure Sensor Input 0.675,5.11 4.159,5.327 3.484,0.216 10 E2: Master Cylinder Pressure Sensor Ground

DTC No. Detection Item DTC Detection Condition Trouble Area
C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) Stored during Test Mode. Brake actuator assembly (Master cylinder pressure sensor)
C1421 Open or Short in Master Cylinder Pressure Sensor Either condition is met:
1.

With the IG1 terminal voltage between 9.5 and 17.4 V, the VCM terminal voltage is not between 4.4 and 5.6 V for 1.2 seconds or more.

2.

When the VCM terminal voltage is between 4.8 and 5.2 V, the PMC terminal voltage is not between 0.19 and 4.57 V for 1.2 seconds or more.


Brake actuator assembly (Master cylinder pressure sensor)
C1423 Master Cylinder Pressure Sensor Zero Point Low Malfunction The PMC terminal voltage is below 0.27 V for 5 seconds or more. Brake actuator assembly (Master cylinder pressure sensor)
C1424 Master Cylinder Pressure Sensor Output Malfunction One of the following conditions is met:
1.

Noise occurs in the PMC terminal signal 7 times or more within 5 seconds.

2.

When the vehicle speed drops from 40 km/h (25 mph) to 0 km/h (0 mph), the master cylinder pressure does not change by at least 0.048 MPa.

3.

At a vehicle speed of 7 km/h (4.3 mph) or more, the PMC terminal voltage is between 0.86 and 1.0 V and the master cylinder pressure does not change by at least 0.048 MPa for 60 seconds or more.

4.

At a vehicle speed of 7 km/h (4 mph) or more, the PMC terminal voltage is 1.0 V or more and the master cylinder pressure does not change by at least 0.048 MPa for 30 seconds or more.

5.

At a vehicle speed of 7 km/h (4 mph) or more with the stop light switch on, a state in which the pressure sensor input value is sufficiently more than the estimated master cylinder pressure continues for 1 second or more and this state occurs 5 or more times each time the ignition switch is turned to ON, and this occurs 8 or more times consecutively.


Brake actuator assembly (Master cylinder pressure sensor)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the brake actuator assembly (master cylinder pressure sensor).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL


Result:
Proceed to
NEXT



NEXT

END