Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.04–2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU.

·

There is a malfunction in the skid control ECU internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU.

·

The anti-lock brake system is defective.


WIRING DIAGRAM

C246481
0.552,0.771 1.51,0.948 0.958,0.177 10 false from IG Circuit 2.563,0.938 2.969,1.198 0.406,0.26 10 false ABS 2.948,0.667 4.021,0.927 1.073,0.26 10 false Reverse Circuit 2.125,1.375 2.521,1.615 0.396,0.24 10 false G19 2.125,1.542 4.448,1.75 2.323,0.208 10 false Combination Meter Assembly 1.906,0.667 2.208,0.948 0.302,0.281 10 false 21 4.375,0.667 4.667,0.906 0.292,0.24 10 false 38 5.25,0.677 5.458,0.823 0.208,0.146 10 false 10 5.583,0.771 5.875,0.938 0.292,0.167 10 false WA 5.573,1.198 5.99,1.365 0.417,0.167 10 false GND1 5.302,1.094 5.417,1.24 0.115,0.146 10 false 1 5.573,1.979 5.844,2.135 0.271,0.156 10 false IG1 5.24,1.844 5.438,2.031 0.198,0.188 10 false 34 2.25,2.125 3.552,2.427 1.302,0.302 10 false ECU-IG&GAUGE 0.563,1.969 1.531,2.135 0.969,0.167 10 false from IG Circuit 5.198,2.792 5.479,2.958 0.281,0.167 10 false A36 5.198,2.969 6.833,3.333 1.635,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 5.552,2.365 6,2.583 0.448,0.219 10 false EXI3 5.229,2.26 5.438,2.417 0.208,0.156 10 false 28 4.104,0.667 4.417,0.896 0.313,0.229 10 false LP 2.146,0.667 2.531,0.896 0.385,0.229 10 false IG+ 2.979,2.365 4.063,2.667 1.083,0.302 10 false from IG Circuit

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Check if DTCs for the ABS are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.135,0.99 0.448,1.177 0.313,0.188 2.01,1.927 2.115,1.927 2.115,1.927 2.292,1.385 false 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 0.167,1.01 0.583,1.271 0.417,0.26 10 false A36 1.75,1.844 2.167,2.104 0.417,0.26 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G19 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-10 (WA) - G19-38 (LP) Always Below 1 Ω
A36-10 (WA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.135,0.99 0.448,1.177 0.313,0.188 1.938,1.906 1.823,1.906 1.823,1.906 1.635,1.396 false 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 0.167,1.01 0.583,1.271 0.417,0.26 10 false A36 1.99,1.823 2.51,2.083 0.521,0.26 10 false EXI3
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-28 (EXI3) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON / OFF Observe the combination meter.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ABS Warning Light
50004 105 8

f.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF ON: ABS warning light on
OFF: ABS warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51
Result:
Result Proceed to
Data List Display Data List Display When Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B




A

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)