Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2012.10
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM C

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0500  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The vehicle speed sensor (SPD1) outputs a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the TCM. The TCM determines the vehicle speed based on the frequency of these pulse signals.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor Malfunction All conditions below are detected 500 times or more continuously (2-trip detection logic):
(a) No signal from vehicle speed sensor (SPD1) is input to TCM while 48 pulses of speed sensor (SP2) signal are sent
(b) Vehicle speed is 9 km/h (6 mph) or more for at least 4 seconds
(c) PNP switch is off (shift lever not in P or N)
·

Open or short in vehicle speed sensor (SPD1) circuit

·

Vehicle speed sensor (SPD1)

·

Combination meter assembly

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C122128
5.927,3.313 6.323,3.49 0.396,0.177 10 false TCM 5.927,3.125 6.323,3.302 0.396,0.177 10 false G41 0.656,2.719 1.052,2.896 0.396,0.177 10 false G19 1.5,1.885 1.719,2.063 0.219,0.177 10 false +S 5.469,1.99 5.688,2.167 0.219,0.177 10 false 25 1.813,1.99 2.031,2.167 0.219,0.177 10 false 6 5.729,1.875 6.167,2.052 0.438,0.177 10 false SPD1 0.656,2.917 1.938,3.094 1.281,0.177 10 false Combination Meter

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

Drive the vehicle.


f.

Read the value displayed on the tester.

Powertrain > ECT > Data List
Tester Display
Vehicle Speed
50003 64 315
Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed Speed indicated on speedometer
OK:

Vehicle speed displayed on tester and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER ASSEMBLY (SPD1 SIGNAL WAVEFORM)
2.CHECK COMBINATION METER ASSEMBLY (SPD1 SIGNAL WAVEFORM)
a.
C217466
0.24,0.708 0.646,0.948 0.406,0.24 2.24,1.604 2.031,0.958 true 0.063,0.042 0.281,0.24 0.219,0.198 10 false *a 0.302,0.75 0.656,0.917 0.354,0.167 10 false G19 2.208,1.604 2.49,1.802 0.281,0.198 10 false +S 2.625,2.375 3.281,2.573 0.656,0.198 10 false 5 V/DIV. 2.76,3.365 3.177,3.563 0.417,0.198 10 false GND 1.708,4.156 2.667,4.344 0.958,0.188 10 false 20 msec./DIV.
*a Component with harness connected(Combination Meter Assembly)


Remove the combination meter assembly with the connector(s) still connected.


b.

Move the shift lever to N.


c.

Jack up the vehicle.


d.

Turn the ignition switch to ON.


e.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition:
Terminal No. (Symbol) Tool Setting Condition
G19-6 (+S) - Body ground 5 V/DIV., 20 msec./DIV. Vehicle speed 20 km/h (12 mph)


OK:

The waveform is displayed as shown in the illustration.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G41 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-6 (+S) - G41-25 (SPD1) Always Below 1 Ω
G19-6 (+S) or G41-25 (SPD1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR