Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2012.10
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052462 AUTOMATIC TRANSMISSION SYSTEM J

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  L4 Position Switch Circuit  


DESCRIPTION

The No. 1 transfer indicator switch (L4 position switch) detects the gear position of the transfer shift lever. Moving the transfer shift lever to L4 turns the L4 position switch is on. Then the TCM cancels operation of the lock-up clutch.

WIRING DIAGRAM

C175018
5.729,2.865 6.063,3.063 0.333,0.198 10 false G40 5.729,3.052 6.281,3.25 0.552,0.198 10 false TCM 5.229,1.479 5.448,1.677 0.219,0.198 10 false 15 2.427,1.688 2.802,1.885 0.375,0.198 10 false C29 3.719,1.458 3.938,1.656 0.219,0.198 10 false 1 2.948,1.458 3.104,1.656 0.156,0.198 10 false 2 2.427,1.875 4.302,2.365 1.875,0.49 10 false No. 1 Transfer Indicator Switch (Transfer L4 position switch) 5.49,1.375 5.708,1.573 0.219,0.198 10 false L4

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - BODY GROUND)
a.
C237849
0.344,0.969 0.781,1.229 0.438,0.26 0.094,0.063 0.365,0.271 0.271,0.208 10 false *a 0.427,1.021 0.708,1.219 0.281,0.198 10 false C29
*a Front view of wire harness connector:
(to No. 1 Transfer Indicator Switch)


Disconnect the C29 No. 1 transfer indicator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT NO.1 TRANSFER INDICATOR SWITCH (L4 POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

2.INSPECT NO.1 TRANSFER INDICATOR SWITCH (L4 POSITION SWITCH)
a.
C237865
0.073,0.042 0.25,0.24 0.177,0.198 10 false *a 0.292,2.958 0.469,3.156 0.177,0.198 10 false *c 0.938,2.969 1.115,3.167 0.177,0.198 10 false *b
*a Component without harness connected
(No. 1 transfer indicator switch)
*b Pushed
*c Not pushed


Remove the No. 1 transfer indicator switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed 10 kΩ or higher
1 - 2 Pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - TCM)

NG

REPLACE NO.1 TRANSFER INDICATOR SWITCH

3.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - TCM)
a.

Disconnect the C29 No. 1 transfer indicator switch connector.


b.

Disconnect the G40 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G40-15 (L4) - C29-1 Always Below 1 Ω
G40-15 (L4) or C29-1 Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR