Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052689 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2780  Push Switch / Key Unlock Warning Switch Malfunction  


DESCRIPTION

This DTC is stored if the transponder key ECU assembly does not detect that the unlock warning switch assembly is on even when the ignition switch is ON. Under normal conditions, the unlock warning switch assembly is on when the ignition switch is ON.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2780 Push Switch / Key Unlock Warning Switch Malfunction The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip detection logic*).
·

Unlock warning switch assembly

·

Harness or connector

·

Transponder key ECU assembly


DTC Output Confirmation Operation

Insert the key into the ignition key cylinder.



*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started. -

Related Data List and Active Test
DTC Code Data List and Active Test
B2780 Key SW

WIRING DIAGRAM

C239010
5.677,0.865 6.156,1.052 0.479,0.188 10 false KSW 5.042,1.604 5.344,1.771 0.302,0.167 10 false G26 5.042,1.792 7.135,1.979 2.094,0.188 10 false Transponder Key ECU Assembly 2.406,1.094 2.708,1.24 0.302,0.146 10 false G10 2.406,1.229 4.5,1.417 2.094,0.188 10 false Unlock Warning Switch Assembly 5.479,0.75 5.615,0.906 0.135,0.156 10 false 3 3.854,0.75 3.99,0.906 0.135,0.156 10 false 1 2.865,0.75 3,0.906 0.135,0.156 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Result:
Proceed to
OK
NG



OK

NG

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.
B274206
0.698,1.073 1.01,1.271 0.313,0.198 10 *a 1.167,1.344 1.479,1.542 0.313,0.198 10 *b
*a Pushed
*b Not pushed


Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pushed Below 1 Ω
Not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - TRANSPONDER KEY ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - TRANSPONDER KEY ECU AND BODY GROUND)
a.

Disconnect the G10 unlock warning switch assembly connector.


b.

Disconnect the G26 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-1 - G26-3 (KSW) Always Below 1 Ω
G10-1 or G26-3 (KSW) - Body ground Always 10 kΩ or higher
G10-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR