Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › from 2012.04
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052695 BLOCKING SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  Engine does not Start  


DESCRIPTION

If the engine does not start and no DTCs are output, the following conditions may apply.

·

There is an open or short circuit between the telephone transceiver assembly and the ECM or transponder key ECU assembly.

·

The blocking system is set.


WIRING DIAGRAM

B315874
3.021,3.042 4.458,3.438 1.438,0.396 10 false Telephone Transceiver Assembly 0.063,2.406 2.667,2.833 2.604,0.427 10 false *1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) 0.063,2.854 1.115,3.052 1.052,0.198 10 false *2: for 2TR-FBE 0.063,3.115 2.917,3.313 2.854,0.198 10 false *3: for 1KD-FTV (for DPF) 2KD-FTV (for DPF) 0.063,3.396 1.792,3.594 1.729,0.198 10 false *4: for 1KD-FTV (for i-ART) 3.021,2.865 3.417,3.031 0.396,0.167 10 false G144 6.531,2.396 6.927,2.573 0.396,0.177 10 false ECM 0.917,1.594 2.01,2 1.094,0.406 10 false Transponder Key ECU Assembly 0.917,1.438 1.198,1.604 0.281,0.167 10 false G26 2.99,0.688 3.354,0.854 0.365,0.167 10 false BLK1 2.833,0.698 2.948,0.865 0.115,0.167 10 false 1 1.885,0.688 2.083,0.854 0.198,0.167 10 false 12 2.833,0.99 2.948,1.156 0.115,0.167 10 false 2 4.26,1.646 4.417,1.813 0.156,0.167 10 false 7 4.26,1.938 4.438,2.104 0.177,0.167 10 false 8 5.958,1.51 6.302,1.677 0.344,0.167 10 false 29*4 5.917,1.729 6.292,1.896 0.375,0.167 10 false G156 5.917,2.01 6.292,2.177 0.375,0.167 10 false G156 5.969,2.229 6.281,2.396 0.313,0.167 10 false 28*4 5.552,1.51 5.896,1.677 0.344,0.167 10 false 29*3 5.531,1.729 5.896,1.896 0.365,0.167 10 false G148 5.531,2.01 5.896,2.177 0.365,0.167 10 false G148 5.573,2.229 5.885,2.396 0.313,0.167 10 false 28*3 5.156,1.51 5.5,1.677 0.344,0.167 10 false 32*2 5.125,1.729 5.5,1.896 0.375,0.167 10 false G146 5.135,2.021 5.51,2.188 0.375,0.167 10 false G146 5.177,2.229 5.49,2.396 0.313,0.167 10 false 31*2 4.75,1.521 5.094,1.688 0.344,0.167 10 false 29*1 4.76,1.719 5.052,1.885 0.292,0.167 10 false G38 4.771,2.021 5.063,2.188 0.292,0.167 10 false G38 4.771,2.229 5.083,2.396 0.313,0.167 10 false 30*1 4.625,0.531 5.104,0.698 0.479,0.167 10 false ECU-B 5.354,0.531 5.708,0.698 0.354,0.167 10 false DCC 1.885,0.99 2.083,1.156 0.198,0.167 10 false 13 0.865,0.844 1.063,1.01 0.198,0.167 10 false 16 1.531,0.771 1.844,0.938 0.313,0.167 10 false EFII 1.49,1.073 1.844,1.24 0.354,0.167 10 false EFIO 1.104,0.948 1.427,1.115 0.323,0.167 10 false GND 2.99,0.979 3.354,1.146 0.365,0.167 10 false BLK4 3.823,1.635 4.188,1.802 0.365,0.167 10 false BLK2 4.24,0.333 4.417,0.5 0.177,0.167 10 false 12 3.99,0.427 4.188,0.594 0.198,0.167 10 false +B 4.26,2.281 4.438,2.448 0.177,0.167 10 false 9 4.063,2.354 4.177,2.521 0.115,0.167 10 false E 6.292,0.417 7.125,0.635 0.833,0.219 10 false from Battery 4.708,0.823 5.01,0.99 0.302,0.167 10 false IGN 4.26,0.625 4.438,0.792 0.177,0.167 10 false 6 3.948,0.698 4.208,0.865 0.26,0.167 10 false IG2 5.448,0.698 6.75,1.167 1.302,0.469 10 false from Ignition Switch Assembly 3.823,1.927 4.188,2.094 0.365,0.167 10 false BLK3 2.99,2.188 4.146,2.542 1.156,0.354 10 false Communication Switch 6.344,1.729 6.708,1.896 0.365,0.167 10 false IMO 6.344,2.042 6.708,2.208 0.365,0.167 10 false IMI

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting this symptom, make sure no engine immobiliser system DTCs or blocking system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs or blocking system DTCs first.

·

When replacing the telephone transceiver assembly, refer to the Service Bulletin.

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK BLOCKING SYSTEM (SETTING)
a.

Check the blocking system setting.

HINT:

Check with the customer's contracted service provider to determine whether the blocking system is set.


Result:
Result Proceed to
Blocking system is set. A
Blocking system is unset. B




A

2.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)

B

UNSET BLOCKING SYSTEM

2.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)
a.
B235876
0.542,1.198 0.958,1.552 0.417,0.354 1,1.802 1.125,1.802 1.125,1.802 1.344,1.51 true 1.344,2.031 1.5,2.031 1.5,2.031 1.563,1.5 true 0.396,2.333 0.708,2.49 0.313,0.156 10 false *1 0.354,0.344 0.667,0.5 0.313,0.156 10 false *a 0.667,1.729 1.125,1.927 0.458,0.198 10 false GND 0.99,1.948 1.448,2.146 0.458,0.198 10 false EFIO 0.615,1.292 1.073,1.49 0.458,0.198 10 false G26 2.99,3.083 3.292,3.229 0.302,0.146 10 false HI 2.99,3.344 3.396,3.542 0.406,0.198 10 false LOW 0.292,3.344 0.75,3.542 0.458,0.198 10 false GND
*1 Waveform
*a Component with harness connected
(Transponder Key ECU Assembly)


Using an oscilloscope, check the waveform.

Measurement Condition:
Item Content
Tester Connection G26-13 (EFIO) - G26-16 (GND)
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON


HINT:
·

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

·

Check the waveform when the security indicator light is off (the engine immobiliser system is unset). If the security indicator light does not turn off (the engine immobiliser system cannot be unset), refer to the engine immobiliser system.



OK:

Waveform is output normally (refer to illustration).


Result:
Result Proceed to
NG (stuck LOW) A
NG (stuck HI) B
OK C




A

3.REPLACE TRANSPONDER KEY ECU ASSEMBLY

B

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

C

6.REGISTER ECU COMMUNICATION ID
3.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

4.REGISTER ECU COMMUNICATION ID
4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER ENGINE STARTS
5.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

6.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY