Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0180  Fuel Temperature Sensor "A" Circuit  P0182  Fuel Temperature Sensor "A" Circuit Low Input  P0183  Fuel Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.

Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change in fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly.

A208462
1.479,2 1.635,1.76 1.635,1.76 1.781,1.76 false 0.208,0.146 0.698,0.385 0.49,0.24 10 false (Fig. 1) 0.208,0.542 1.198,0.75 0.99,0.208 10 false Resistance kΩ 1.813,1.667 2.542,1.823 0.729,0.156 10 false Acceptable 1.208,4.063 2.542,4.323 1.333,0.26 10 false Temperature °C (°F)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0180 Fuel Temperature Sensor "A" Circuit Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor (fuel supply pump assembly)

·

ECM


Comes on DTC stored
P0182 Fuel Temperature Sensor "A" Circuit Low Input Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in fuel temperature sensor circuit

·

Fuel temperature sensor (fuel supply pump assembly)

·

ECM


Comes on DTC stored
P0183 Fuel Temperature Sensor "A" Circuit High Input Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in fuel temperature sensor circuit

·

Fuel temperature sensor (fuel supply pump assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0180 Fuel Temp
P0182
P0183

HINT:
·

If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

Lack of power


·

When DTC P0180, P0182 and/or P0183 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



CONFIRMATION DRIVING PATTERN

P0180, P0182, P0183
DTC Detection Drive Pattern Ignition switch to ON for 0.5 seconds

WIRING DIAGRAM

A210074
0.635,2.135 2.26,2.344 1.625,0.208 10 false Fuel Temperature Sensor 5.958,2.438 6.354,2.615 0.396,0.177 10 false ECM 6.25,0.208 6.479,0.385 0.229,0.177 10 false 5 V 5.552,0.646 5.906,0.823 0.354,0.177 10 false THF 5.552,1.26 6.01,1.438 0.458,0.177 10 false E2 6.167,0.531 6.323,0.708 0.156,0.177 10 false R 2.448,1.281 2.563,1.469 0.115,0.188 10 false 1 2.448,0.667 2.563,0.844 0.115,0.177 10 false 2 5.24,0.646 5.51,0.823 0.271,0.177 10 false 29 5.25,1.271 5.458,1.448 0.208,0.177 10 false 28 0.635,1.948 0.917,2.135 0.281,0.188 10 false C19 5.958,2.281 6.396,2.427 0.438,0.146 10 false C22

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

d.

Read the value.

OK:

Same as the actual fuel temperature


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (Same as actual fuel temperature) C


HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A204471
0.646,3.365 1.031,3.604 0.385,0.24 0.708,3.396 1.031,3.594 0.323,0.198 10 false C19 0.677,2.698 0.99,2.896 0.313,0.198 10 false *a 2.396,1.531 2.708,1.729 0.313,0.198 10 false E2 2.385,1.042 2.844,1.24 0.458,0.198 10 false THF 0.635,0.292 0.979,0.51 0.344,0.219 11 false *1 2.646,0.26 2.958,0.458 0.313,0.198 10 false *2
*1 Fuel Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Fuel Temperature Sensor)


Disconnect the fuel temperature sensor connector.


b.

Connect terminals 2 and 1 of the fuel temperature sensor connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

f.

Read the value.

OK:

140°C (284°F) or higher



g.

Reconnect the fuel temperature sensor connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
3.REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SUPPLY PUMP(w/o DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C19-2 - C22-29 (THF) Always Below 1 Ω
C19-1 - C22-28 (E2) Always Below 1 Ω



d.

Reconnect the fuel temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A204586
0.792,0.146 1.135,0.427 0.344,0.281 10 false *1 2.615,0.125 2.979,0.396 0.365,0.271 10 false *2 2.396,0.969 2.75,1.25 0.354,0.281 10 false THF 2.427,1.438 2.771,1.688 0.344,0.25 10 false E2
*1 Fuel Temperature Sensor
*2 ECM


Disconnect the fuel temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the fuel temperature sensor connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)

NG

10.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SUPPLY PUMP(w/o DPF)>COMPONENTS


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

9.PERFORM FUEL SUPPLY PUMP INITIALIZATION
9.PERFORM FUEL SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C19-2 or C22-29 (THF) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 1 second or more.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END