Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P1601  Injector Correction Circuit Malfunction (EEPROM)  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1601 Injector Correction Circuit Malfunction (EEPROM) Any condition is met (1 trip detection logic):
·

Injector compensation code is not registered.

·

Incorrect injector compensation code is registered.

·

Injector pilot quantity learning value is not registered.


·

Injector compensation code

·

Injector pilot quantity learning value

·

ECM


Comes on DTC stored

NOTICE:
·

When a injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

When a injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing injector pilot quantity learning values must be input into the new ECM.



HINT:

When replacing the ECM with a new one, if the injector compensation code and/or injector pilot quantity learning value are not entered, DTC P1601 will be stored.


When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:


a.

Prior to replacing the ECM, use the intelligent tester to read and save each learning value and code from the original ECM (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION).


b.

After installing a new ECM, input the saved learning values and codes into the new ECM using the tester (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION).


c.

Turn the ignition switch off and turn the tester off.


d.

Wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the tester on.


f.

Clear the DTC P1601 stored in the ECM using the tester (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR).

HINT:
·

Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.

·

When you first turn the ignition switch to ON after replacing the ECM and one or more other components, DTC P1601 is stored. Manually clear the DTC upon completion of compensation code registration.

Replacement Part Utility Item
ECM
·

Learning Values Save (See page (Click here))

·

Learning Values Write (See page (Click here))


Injector assembly
·

Input Injector Compensation Code (See page (Click here))

·

Pilot Quantity Learning (See page (Click here))







CONFIRMATION DRIVING PATTERN

P1601
DTC Detection Drive Pattern Ignition switch to ON for 1 second

CAUTION / NOTICE / HINT

PROCEDURE

1.LEARNING VALUES CONFIRMATION
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Confirmation
50005 61 242
Result:
Result Proceed to
The injector compensation codes are not input A
The injector compensation codes registered in the ECM are different than the codes imprinted on the injector assemblies
The pilot quantity learning values are set to the default values B
Except above C


HINT:

When the injector pilot quantity learning values are set to the default values, "7FFF" is displayed.




A

2.REGISTER INJECTOR COMPENSATION CODE

B

3.LEARNING VALUES WRITE

C

6.CHECK DTC OUTPUT
2.REGISTER INJECTOR COMPENSATION CODE

Result:
Proceed to
NEXT



NEXT

5.PILOT QUANTITY LEARNING
3.LEARNING VALUES WRITE
HINT:

When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the intelligent tester and replacing the old ECM with a new one, "Learning Values Write" was not performed using the intelligent tester causing this DTC to be output.


a.

Install the old ECM.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Save
50005 61 240

e.

Remove the old ECM.


f.

Install a new ECM.


g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Write
50005 61 241

Result:
Proceed to
NEXT



NEXT

4.LEARNING VALUES CONFIRMATION
4.LEARNING VALUES CONFIRMATION
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Confirmation
50005 61 242
Result:
Result Proceed to
The pilot quantity learning values are set to the default values A
Except above B


HINT:

When the injector pilot quantity learning values are set to the default values, "7FFF" is displayed.




A

5.PILOT QUANTITY LEARNING

B

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.PILOT QUANTITY LEARNING
a.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs .

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
P1601 is output B




A

END

B

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END