Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) J

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The MREL output signal from ECM causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A255066
2.771,0.906 3.75,1.135 0.979,0.229 10 false Ignition Switch 2.771,0.76 3.01,0.927 0.24,0.167 10 false G9 1.396,0.51 1.875,0.729 0.479,0.219 10 false AM2 2.833,0.49 3.177,0.656 0.344,0.167 10 false AM2 1.25,1.677 2.042,1.979 0.792,0.302 10 false BATT P/I 0.813,2.531 1.427,2.802 0.615,0.271 10 false Battery 3.333,0.49 3.615,0.656 0.281,0.167 10 false IG2 4.01,2.26 4.51,2.479 0.5,0.219 10 false MAIN 3.292,2.594 4.802,2.854 1.51,0.26 10 false No. 1 Integration Relay 3.156,1.615 3.479,1.802 0.323,0.188 10 false EFI 2.656,1.5 2.927,1.667 0.271,0.167 10 false 1H 2.667,1.958 2.958,2.135 0.292,0.177 10 false 1J 4.76,1.5 4.979,1.677 0.219,0.177 10 false 1J 4.76,1.958 4.979,2.135 0.219,0.177 10 false 1J 4.656,0.5 5.042,0.75 0.385,0.25 10 false IGN 5.635,0.365 5.979,0.542 0.344,0.177 10 false G39 5.635,1.49 5.979,1.667 0.344,0.177 10 false G39 5.635,1.969 5.979,2.146 0.344,0.177 10 false G39 5.646,2.417 6,2.573 0.354,0.156 10 false C23 5.99,0.333 6.438,0.521 0.448,0.188 10 false IGSW 5.979,1.479 6.333,1.698 0.354,0.219 10 false +B 5.99,1.948 6.469,2.135 0.479,0.188 10 false MREL 5.99,2.438 6.24,2.594 0.25,0.156 10 false E1 6.198,3.125 6.667,3.354 0.469,0.229 10 false ECM 2.688,1.313 2.854,1.479 0.167,0.167 10 false 1 3.115,1.333 3.281,1.5 0.167,0.167 10 false 1 5.729,1.26 5.896,1.427 0.167,0.167 10 false 1 4.802,1.771 4.969,1.938 0.167,0.167 10 false 2 3.354,1.333 3.521,1.5 0.167,0.167 10 false 2 2.677,0.469 2.792,0.635 0.115,0.167 10 false 5 3.646,0.469 3.813,0.635 0.167,0.167 10 false 6 2.688,1.76 2.854,1.927 0.167,0.167 10 false 3 4.802,1.302 4.969,1.469 0.167,0.167 10 false 4 5.729,0.125 5.896,0.292 0.167,0.167 10 false 9 5.729,2.229 5.896,2.396 0.167,0.167 10 false 7 5.729,1.75 5.896,1.917 0.167,0.167 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.



PROCEDURE

1.INSPECT ECM (+B VOLTAGE)
a.
A080463
1.24,0.198 1.615,0.458 0.375,0.26 2.469,0.198 2.844,0.458 0.375,0.26 1.167,0.802 0.917,1.51 false 2.99,0.792 3,1.531 false 1.313,0.25 1.594,0.448 0.281,0.198 10 false C23 2.542,0.24 2.823,0.438 0.281,0.198 10 false G39 0.698,1.583 1.271,1.896 0.573,0.313 10 false 7 (E1) 2.781,1.563 3.333,1.854 0.552,0.292 10 false 1 (+B) 0.083,0.083 0.313,0.26 0.229,0.177 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G39-1 (+B) - C23-7 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C23-7 (E1) - Body ground Always Below 1 Ω



c.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (IGSW VOLTAGE)
a.
A080463
1.24,0.198 1.615,0.458 0.375,0.26 2.49,0.198 2.865,0.458 0.375,0.26 1.167,0.802 0.917,1.51 false 2.958,0.896 2.531,1.5 false 1.292,0.25 1.573,0.448 0.281,0.198 10 false C23 2.552,0.25 2.833,0.448 0.281,0.198 10 false G39 0.646,1.552 1.156,1.854 0.51,0.302 10 false 7 (E1) 2.219,1.563 2.865,1.833 0.646,0.271 10 false 9 (IGSW) 0.104,0.094 0.313,0.292 0.208,0.198 10 false *a
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G39-9 (IGSW) - C23-7 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (MREL VOLTAGE)

NG

7.INSPECT IGNITION SWITCH
4.INSPECT ECM (MREL VOLTAGE)
a.
A080463
1.24,0.198 1.615,0.458 0.375,0.26 2.51,0.198 2.885,0.458 0.375,0.26 1.167,0.802 0.917,1.51 false 3,0.885 3.031,1.49 false 1.292,0.25 1.573,0.448 0.281,0.198 10 false C23 2.573,0.24 2.854,0.438 0.281,0.198 10 false G39 0.656,1.563 1.208,1.823 0.552,0.26 10 false 7 (E1) 2.604,1.542 3.313,1.823 0.708,0.281 10 false 8 (MREL) 0.083,0.094 0.271,0.292 0.188,0.198 10 false *a
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G39-8 (MREL) - C23-7 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 INTEGRATION RELAY (MAIN RELAY)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (MAIN RELAY)
a.

Inspect the No. 1 integration relay (MAIN relay).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MAIN RELAY - ECM, MAIN RELAY - BODY GROUND)

NG

REPLACE INTEGRATION NO.1 RELAY (MAIN RELAY)

6.CHECK HARNESS AND CONNECTOR (MAIN RELAY - ECM, MAIN RELAY - BODY GROUND)
a.

Check the harness and connector between the No. 1 integration relay (MAIN relay) and ECM.

i.

Remove the integration relay (MAIN relay) from the No. 1 engine room R/B and J/B.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-4 - G39-1 (+B) Always Below 1 Ω
1J-2 - G39-8 (MREL) Always Below 1 Ω
1J-4 or G39-1 (+B) - Body ground Always 10 kΩ or higher
1J-2 or G39-8 (MREL) - Body ground Always 10 kΩ or higher



iv.

Reconnect the ECM connector.


v.

Reinstall the No. 1 integration relay.



b.

Check the harness and connector between the integration relay (MAIN relay) and body ground.

i.

Remove the No. 1 integration relay (MAIN relay) from the No. 1 engine room R/B and J/B.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-3 - Body ground Always Below 1 Ω



iii.

Reinstall the No. 1 integration relay.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH
a.
B119736
1.292,1.75 1.656,1.344 true 2.021,1.344 2.406,1.75 true 0.135,0.104 0.542,0.406 0.406,0.302 10 false *1 2.292,1.781 2.823,2.063 0.531,0.281 10 false AM2 1.063,1.792 1.396,2.031 0.333,0.24 10 false IG2
*1 Ignition Switch


Disconnect the ignition switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (AM2) - 6 (IG2) LOCK 10 kΩ or higher
5 (AM2) - 6 (IG2) ON Below 1 Ω



c.

Reconnect the ignition switch connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM)

NG