*: Use the intelligent tester.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
If the display indicates a communication fault in the tester, inspect the DLC3.
| Proceed to |
|---|
| NEXT |
NEXT
Check DTC.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Check freeze frame data.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
Record or print DTCs and freeze frame data, if necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Clear DTC and freeze frame data.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Switch the ECM from the normal mode to check mode.
Refer to Check Mode Procedure.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Confirm problem symptoms.
Refer to Problem Symptoms Table.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
If the engine does not start, first perform the "Check DTC" procedures and "Conduct Basic Inspection" procedures below.
| Result | Proceed to |
|---|---|
| Malfunction does not occur | A |
| Malfunction occurs | B |
A
B
Refer to Symptom Simulation.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Refer to DTC Check / Clear.
| Result | Proceed to |
|---|---|
| Trouble code output | A |
| No code output | B |
A
B
Refer to Diagnostic Trouble Code Chart.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Proceed to |
|---|
| NEXT |
NEXT
Conduct basic inspection.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>BASIC INSPECTION
| Result | Proceed to |
|---|---|
| Malfunctioning parts not confirmed | A |
| Malfunctioning parts confirmed | B |
A
B
Refer to Problem Symptoms Table.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Malfunctioning circuit confirmed | A |
| Malfunctioning parts confirmed | B |
A
B
Check the ECM power source circuit.
Refer to ECM Power Source Circuit.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit
| Proceed to |
|---|
| NEXT |
NEXT
| Result | Proceed to |
|---|---|
| Malfunction not confirmed | A |
| Malfunction confirmed | B |
A
B
Check for intermittent problems.
Refer to Check for Intermittent Problems.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT