Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2013.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF OFF -
Brake Warning Light Brake warning light ON or OFF ON: Brake warning light on
OFF: Brake warning light off
-
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Main Idle SW Main idle switch ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Gear Position Gear position information P,N, R, 1st-8th, Fail, Not R Actual gear position -
Shift Lever Position Shift lever position information P,N, R, D/M, 1st-6th/B, Fail Actual shift lever position -
Shift Information Shift information ON or OFF ON: During gear change
OFF: Not during gear change
-
Inspection Mode Inspection mode Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Number of IG ON(Inspection) Number of times ignition switch turned on after entering inspection mode Min.: 0, Max.: 255 - -
Master Cylinder Sensor Master cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.3 to 0.9 V The value increases when the brake pedal is depressed.
Zero Point of M/C Memorized zero value Min.: -12.50 Mpa, Max.: 12.40 Mpa - -
Deceleration Sensor Acceleration sensor (GL1) Min.: -18.525 m/s2, Max.: 18.387 m/s2 - Changes continuously during acceleration/deceleration.
Zero Point of Decele Memorized zero value Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Deceleration Sensor2 Acceleration sensor (GL2) Min.: -18.525 m/s2, Max.: 18.387 m/s2 - Changes continuously during acceleration/deceleration.
Zero Point of Decele2 Memorized zero value Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s, Max.: 127°/s Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Zero Point of Yaw Rate Memorized zero value Min.: -128°, Max.: 127° - -
Yaw Rate Sensor2 Yaw rate sensor 2 Min.: -128°/s, Max.: 127°/s Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Zero Point of Yaw Rate2 Memorized zero value Min.: -128°/s, Max.: 127°/s - -
Steering Angle Sensor Steering angle sensor Min.: -3276.8°, Max.: 3276.7° Left turn: Increases
Right turn: Decreases
-
Zero Point of Steering Angle Memorized zero value Min.: -3276.8°, Max.: 3276.7° After steering angle sensor zero point calibration: 0° -
Lateral G Lateral G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - Changes in proportion to acceleration during turning.
Forward and Rearward G Forward and backward G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - Changes in proportion to acceleration during acceleration/deceleration.
Yaw Rate Value Yaw rate value Min.: -128°/s, Max.: 127°/s - Changes in proportion to yaw during turning.
Steering Angle Value Steering angle value Min.: -3276.8°, Max.: 3276.7° - Changes in proportion to the amount of steering wheel rotation during steering operation.
Slip Indicator Light Slip indicator light ON or OFF ON: Slip indicator light on
OFF: Slip indicator light off
-
Rear Diff Lock Switch Rear differential lock detection switch ON or OFF OFF -
Automatic Disconnect Diff SW 4WD detection switch ON or OFF for 4WD:
ON: 4WD
OFF: 2WD
for 2WD:
OFF
-
L4 Switch L4 position switch ON or OFF for 4WD:
ON: L4
OFF: except L4
for 2WD:
OFF
-
FR Wheel Speed Front speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
Vehicle Speed Maximum speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed.
FR Wheel Acceleration Front wheel RH acceleration Min.: -200.84 m/s2, Max.: 199.27 m/s2 - Changes continuously during acceleration/deceleration.
FL Wheel Acceleration Front wheel LH acceleration Min.: -200.84 m/s2, Max.: 199.27 m/s2 - Changes continuously during acceleration/deceleration.
RR Wheel Acceleration Rear wheel RH acceleration Min.: -200.84 m/s2, Max.: 199.27 m/s2 - Changes continuously during acceleration/deceleration.
RL Wheel Acceleration Rear wheel LH acceleration Min.: -200.84 m/s2, Max.: 199.27 m/s2 - Changes continuously during acceleration/deceleration.
FR Wheel ABS Ctrl Status Front wheel RH ABS control status ON or OFF ON: During control
OFF: Not during control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status ON or OFF ON: During control
OFF: Not during control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status ON or OFF ON: During control
OFF: Not during control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status ON or OFF ON: During control
OFF: Not during control
-
RR Wheel EBD Ctrl Status Rear wheel RH EBD control status ON or OFF ON: During control
OFF: Not during control
-
RL Wheel EBD Ctrl Status Rear wheel LH EBD control status ON or OFF ON: During control
OFF: Not during control
-
BA Ctrl Status BA control status ON or OFF ON: During control
OFF: Not during control
-
TRC(TRAC) Ctrl Status TRC control status ON or OFF ON: During control
OFF: Not during control
-
TRC(TRAC) Engine Ctrl Status TRC engine control status ON or OFF ON: During control
OFF: Not during control
-
TRC(TRAC) Brake Ctrl Status TRC brake control status ON or OFF ON: During control
OFF: Not during control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status ON or OFF ON: During control
OFF: Not during control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status ON or OFF ON: During control
OFF: Not during control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status ON or OFF ON: During control
OFF: Not during control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status ON or OFF ON: During control
OFF: Not during control
-
Engine Revolutions Engine speed Min.: 0 rpm, Max.: 65535 rpm Engine stopped: 0 rpm No large fluctuations when the engine speed is constant.
Real Engine Torque Actual engine torque Min.: -1024.0 Nm, Max.: 1023.0 Nm - -
Accelerator Opening Angle % Throttle valve opening amount Min.: 0.0%, Max.: 128.0% When accelerator pedal released: 0% Changes in proportion to the movement of the pedal during accelerator pedal operation.
Solenoid Relay Solenoid relay ON or OFF ON: Solenoid relay on
OFF: Solenoid relay off
-
ECB Motor Relay Motor relay ON or OFF ON: Motor relay on
OFF: Motor relay off
ECB: Electronically Controlled Brake
Fail Safe Motor Relay Motor fail-safe relay ON or OFF ON: Motor fail-safe relay on
OFF: Motor fail-safe relay off
-
TR(A)C/VSC Solenoid (SM2) Master cylinder cut solenoid (SM2) ON or OFF ON: Operating
OFF: Not operating
-
TR(A)C/VSC Solenoid (SM1) Master cylinder cut solenoid (SM1) ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRH) Front wheel RH hold solenoid ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRR) Front wheel RH release solenoid ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLH) Front wheel LH hold solenoid ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLR) Front wheel LH release solenoid ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRH) Rear wheel RH hold solenoid ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRR) Rear wheel RH release solenoid ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLH) Rear wheel LH hold solenoid ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLR) Rear wheel LH release solenoid ON or OFF ON: Operating
OFF: Not operating
-
FR Speed Open Front speed sensor RH open circuit detection Error or Normal Normal -
FL Speed Open Front speed sensor LH open circuit detection Error or Normal Normal -
RR Speed Open Rear speed sensor RH open circuit detection Error or Normal Normal -
RL Speed Open Rear speed sensor LH open circuit detection Error or Normal Normal -
EFI Communication Open EFI communication open circuit detection Error or Normal Normal -
Yaw Rate Open Yaw rate sensor open circuit detection Error or Normal Normal -
Deceleration Open Acceleration sensor open circuit detection Error or Normal Normal -
Steering Open Steering angle sensor open circuit detection Error or Normal Normal -
Master Cylinder Open Master cylinder pressure sensor open circuit detection Error or Normal Normal -
IG1 Voltage Value IG1 voltage Min.: 0.00 V, Max.: 20.00 V 11 to 14 V -
MT Voltage Value Monitor voltage Min.: 0.00 V, Max.: 20.00 V - -
TRC/VSC Off Mode VSC OFF switch Normal, Unknown, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Number of DTC Number of DTCs stored Min.: 0, Max.: 255 - -
IG Voltage Value Decreased IG voltage value decrease detection Error or Normal Normal -
IG Voltage Value Increased IG voltage value increase detection Error or Normal Normal -
FR Speed Sensor Voltage Open Front speed sensor RH voltage open circuit detection Error or Normal Normal -
FL Speed Sensor Voltage Open Front speed sensor LH voltage open circuit detection Error or Normal Normal -
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open circuit detection Error or Normal Normal -
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open circuit detection Error or Normal Normal -
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Error or Normal Normal -
Brake Pedal Switch Open Brake pedal load sensing switch open circuit detection Error or Normal Normal -
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open circuit detection Error or Normal Normal -
EFI Communication Invalid EFI communication invalid detection Error or Normal Normal -


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


f.

According to the display on the GTS, perform the Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON / OFF Observe the combination meter.
Brake Warning Light Brake warning light Warning light ON / OFF Observe the combination meter.
Solenoid Relay Solenoid relay Relay ON / OFF When Solenoid Relay is turned OFF using the Active Test, the slip indicator light turns on.
Motor Relay Motor relay Relay ON / OFF The operating sound of the motor can be heard.
ABS Solenoid (SRLR) Rear wheel LH release solenoid Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRLH) Rear wheel LH hold solenoid Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRR) Rear wheel RH release solenoid Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRH) Rear wheel RH hold solenoid Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLR) Front wheel LH release solenoid Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLH) Front wheel LH hold solenoid Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRR) Front wheel RH release solenoid Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRH) Front wheel RH hold solenoid Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SMR) Master cylinder cut solenoid (SM2) Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SMF) Master cylinder cut solenoid (SM1) Solenoid ON / OFF The operating sound of the solenoid (clicking sound) can be heard.
TRC(TRAC) OFF Indicator Light TRC OFF indicator light Indicator light ON / OFF Observe the combination meter.
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON / OFF Observe the combination meter.
Slip Indicator Light Slip indicator light Indicator light ON / OFF Observe the combination meter.
ABS Solenoid Holding solenoids (SFRH, SFLH, SRRH and SRLH) and release solenoids (SFRR, SFLR, SRRR and SRLR) Start/Stop Start: When Start is selected, the selected solenoids turn ON.
Stop: When Stop is selected, the selected solenoids turn OFF.
HINT:

Selection of multiple holding solenoids and release solenoids is possible.


VSC/TRC(TRAC) Solenoid Master cylinder cut solenoids SMR (SM2) and SMF (SM1) Start/Stop Start: When Start is selected, the selected solenoids turn ON.
Stop: When Stop is selected, the selected solenoids turn OFF.
HINT:

Selection of multiple master cylinder cut solenoids is possible.