Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2013.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

If the skid control ECU (brake actuator assembly) stores a DTC, the slip indicator light in the combination meter comes on.

The slip indicator light blinks during VSC and TRC operation.

WIRING DIAGRAM

C288640
0.208,0.813 1.177,1.052 0.969,0.24 10 false from IG Circuit 1.583,0.813 1.969,1.063 0.385,0.25 10 false G19 1.656,0.604 1.865,0.833 0.208,0.229 10 false 21 1.979,0.698 2.271,0.917 0.292,0.219 10 false IG+ 3.396,1.031 3.688,1.26 0.292,0.229 10 false Slip 3.979,0.708 4.365,0.948 0.385,0.24 10 false SLIP 4.427,0.813 4.719,1.021 0.292,0.208 10 false G20 4.5,0.604 4.708,0.833 0.208,0.229 10 false 17 5.646,0.813 6.031,1.052 0.385,0.24 10 false IND 5.406,0.708 5.542,0.958 0.135,0.25 10 false 3 5.625,1.635 6.052,1.844 0.427,0.208 10 false GND1 5.417,1.51 5.552,1.76 0.135,0.25 10 false 1 5.667,2.365 6.094,2.573 0.427,0.208 10 false IG1 5.365,2.229 5.573,2.458 0.208,0.229 10 false 34 2.188,1.365 4.083,1.625 1.896,0.26 10 false Combination Meter Assembly 0.406,2.333 1.375,2.573 0.969,0.24 10 false from IG Circuit 2.198,2.542 3.167,2.781 0.969,0.24 10 false ECU-IG NO. 2 5.375,2.875 5.688,3.083 0.313,0.208 10 false A36 5.375,3.052 6.917,3.417 1.542,0.365 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK FOR DTC
a.

Check if DTCs for the VSC are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIP INDICATOR LIGHT)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIP INDICATOR LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Slip Indicator Light Slip indicator light Indicator light ON / OFF Observe the combination meter.

f.

When performing the Slip Indicator Light Active Test, check Slip Indicator Light in the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Slip Indicator Light Slip indicator light ON or OFF ON: Slip indicator light on
OFF: Slip indicator light off
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Slip Indicator Light
Data List Display
Slip Indicator Light
50004 105 11 53

Result:
Result Proceed to
Data List Display Data List Display When Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B



A

B

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G20 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-3 (IND) - G20-17 (SLIP) Always Below 1 Ω
A36-3 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR