Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 4WD and Pre-Runner) › from 2013.10
RM1840EF _54 Brake _009625 BRAKE (FRONT) _0052625 FRONT BRAKE(for 4WD and Pre-Runner) A

BRAKE (FRONT)  FRONT BRAKE(for 4WD and Pre-Runner)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 3.REMOVE FRONT DISC BRAKE ANTI-RATTLE SPRING

a.

for 15 inch Front Disc Brake (Type A):

i.
C111375
2.396,0.438 2.917,0.438 true 1.333,0.76 0.531,0.76 true 1.583,1.396 0.615,1.396 true 2.948,0.354 3.135,0.531 0.188,0.177 10 false *2 0.365,0.677 0.542,0.844 0.177,0.167 10 false *1 0.448,1.323 0.635,1.521 0.188,0.198 10 false *3
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the pin hold clip.


ii.

Hold down the anti-rattle spring and remove the 2 disc brake pad guide pins.


iii.

Remove the anti-rattle spring.

CAUTION:

Do not remove the 2 disc brake pad guide pins without holding down the anti-rattle spring. The anti-rattle spring will eject with a force capable of causing injury.




b.

for 15 inch Front Disc Brake (Type B):

i.
C215909
0.823,0.323 0.25,0.323 false 2.271,1.292 2.615,1.792 2.615,1.792 2.854,1.792 false 1.604,1.531 1.073,1.292 1.073,1.292 0.448,1.292 false 0.073,0.25 0.271,0.417 0.198,0.167 10 false *1 2.896,1.719 3.115,1.896 0.219,0.177 10 false *2 0.26,1.229 0.458,1.406 0.198,0.177 10 false *3
*1 Disc Brake Pad Guide Pin
*2 Pin Hpld Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the pin hold clip and 2 disc brake pad guide pins.


ii.

Remove the anti-rattle spring.

NOTICE:

The anti-rattle spring can be reused if it has sufficient rebound; no deformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.




c.

for 16 inch Front Disc Brake:

i.
C281987
0.563,0.292 0.802,0.292 false 2.115,0.208 2.208,0.563 2.208,0.563 2.417,0.563 false 1.719,1.427 1.583,1.281 1.583,1.281 1.302,1.281 false 2.323,1.604 2.323,1.365 2.323,1.365 2.479,1.365 false 0.354,0.208 0.563,0.406 0.208,0.198 10 true *1 2.479,0.469 2.792,0.625 0.313,0.156 10 false *2 1.073,1.208 1.385,1.365 0.313,0.156 10 false *3 2.531,1.302 2.844,1.458 0.313,0.156 10 false *2
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the 2 pin hold clips and 2 disc brake pad guide pins.


ii.

Remove the anti-rattle spring.

NOTICE:

The anti-rattle spring can be reused if it has sufficient rebound; no deformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.




d.

for 16 inch Front Disc Brake:

(for TDV, TASA Made)

i.
C263522
1.385,0.719 0.792,0.385 0.792,0.385 0.625,0.385 true 2.354,0.24 3,0.24 true 2.531,1.406 2.99,1.406 true 1.604,1.188 0.625,1.188 true 0.427,0.313 0.583,0.458 0.156,0.146 10 false *1 3.01,0.146 3.177,0.302 0.167,0.156 10 false *2 3.01,1.323 3.177,1.469 0.167,0.146 10 false *2 0.427,1.104 0.594,1.25 0.167,0.146 10 false *3
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the 2 pin hold clips and 2 disc brake pad guide pins.


ii.

Hold down the anti-rattle spring and remove the 2 disc brake pad guide pins.


iii.

Remove the anti-rattle spring.

CAUTION:

Do not remove the 2 disc brake pad guide pins without holding down the anti-rattle spring. The anti-rattle spring will eject with a force capable of causing injury.




Hide 4.REMOVE FRONT DISC BRAKE PAD

a.

Remove the 2 front disc brake pads from the disc brake cylinder.


Hide 5.REMOVE FRONT ANTI-SQUEAL SHIM KIT

a.

Remove the 2 No. 1 anti-squeal shims and 2 No. 2 anti-squeal shims from each pad.


Hide 6.DISCONNECT FRONT NO. 1 WHEEL CYLINDER TUBE LH

a.
C111376

Using a union nut wrench, disconnect the tube from the cylinder.


Hide 7.REMOVE DISC BRAKE CYLINDER ASSEMBLY LH

a.
C111377

Remove the 2 bolts and disc brake cylinder.


Hide 8.REMOVE FRONT DISC

a.
C111383
2.135,1.115 2.135,0.188 2.135,0.188 1.115,0.188 true 2.115,1.26 1.948,1.26 1.948,1.26 1.948,0.188 true 0.906,0.104 1.083,0.271 0.177,0.167 10 false *1
*1 Matchmark


Put matchmarks on the disc and axle hub.


b.

Remove the disc.