Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Radio and Display Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009633 PARK ASSIST / MONITORING _0052662 REAR VIEW MONITOR SYSTEM(for Radio and Display Type) U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Radio and Display Type)  TERMINALS OF ECU  


CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


E275626
1.729,0.333 2.135,0.573 0.406,0.24 1.417,1.448 1.823,1.688 0.406,0.24 4.51,0.344 4.917,0.583 0.406,0.24 1.75,0.365 2.188,0.552 0.438,0.188 10 false G158 1.458,1.49 1.896,1.677 0.438,0.188 10 false G129 4.531,0.385 4.969,0.573 0.438,0.188 10 false G127

a.

Disconnect the G127 and G129 radio and display receiver assembly connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G127-1 (IG) - G129-7 (GND) P - BR IG signal Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
G129-3 (ACC) - G129-7 (GND) GR - BR ACC signal Ignition switch off Below 1 V
Ignition switch ACC 11 to 14 V
G129-4 (B) - G129-7 (GND) L-Y - BR Battery Always 11 to 14 V
G129-7 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G127 and G129 radio and display receiver assembly connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G127-2 (REV) - G129-7 (GND) R-Y - BR Reverse signal Ignition switch ON, shift lever in R 7.5 to 14 V
Ignition switch ON, shift lever not in R Below 1 V
G158-11 (CA+) - G158-23 (CGND) B - Shielded Power source Ignition switch ACC 5.5 to 7.05 V
G158-12 (V+) - G158-24 (V-) W - R Display signal Ignition switch ON, shift lever in R Pulse generation
(See waveform 1)
Ignition switch ON, shift lever in R, screen blacked out by covering camera lens Pulse generation
(See waveform 2)
G158-23 (CGND) - Body ground Shielded - Body ground Shielding Always Below 1 V

If the result is not as specified, the radio and display receiver assembly may have a malfunction.


e.

Using an oscilloscope, check the waveform.

E272452
1.01,2.333 1.188,2.333 1.188,2.333 1.302,1.865 false 1.781,2.333 1.625,2.333 1.625,2.333 1.417,1.771 false 5.063,2.292 4.906,2.292 4.906,2.292 4.667,1.625 false 4.25,2.292 4.427,2.292 4.427,2.292 4.542,1.698 false 0.563,1.302 1.021,1.5 0.458,0.198 10 false GND 3.771,1.281 4.229,1.479 0.458,0.198 10 false GND 0.458,0.313 0.917,0.51 0.458,0.198 10 false *a 3.698,0.26 4.156,0.458 0.458,0.198 10 false *b 0.844,2.24 1.302,2.438 0.458,0.198 10 false *c 1.833,2.25 2.292,2.448 0.458,0.198 10 false *d 4.115,2.198 4.573,2.396 0.458,0.198 10 false *c 5.135,2.229 5.594,2.427 0.458,0.198 10 false *d
*a Waveform 1 *b Waveform 2
*c Synchronized Signal *d Video Waveform


i.

Waveform 1

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Measurement Condition
Item Content
Terminal No. (Symbol) G158-12 (V+) - G158-24 (V-)
Tool Setting 0.2 V/DIV., 50 μs/DIV.
Condition Ignition switch ON, shift lever in R


ii.

Waveform 2

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Measurement Condition
Item Content
Terminal No. (Symbol) G158-12 (V+) - G158-24 (V-)
Tool Setting 0.2 V/DIV., 50 μs/DIV.
Condition Ignition switch ON, shift lever in R, screen blacked out by covering camera lens