Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the navigation receiver assembly via this circuit.

The sound signal that has been sent is amplified by the navigation receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.

WIRING DIAGRAM

E278091
1.313,0.708 1.667,0.906 0.354,0.198 10 false 10 0.865,1.271 1.479,1.469 0.615,0.198 10 false VAR+ 0.885,1.75 1.5,1.948 0.615,0.198 10 false VAL+ 0.948,2.198 1.563,2.396 0.615,0.198 10 false VA- 0.844,2.698 1.458,2.896 0.615,0.198 10 false AGND 0.375,3.146 0.99,3.344 0.615,0.198 10 false z8 0.396,3.333 1.604,3.698 1.208,0.365 10 false No. 1 Stereo Jack Adapter Assembly 2.563,2.896 3.177,3.094 0.615,0.198 10 false Shielded 5.927,0.813 6.542,1.01 0.615,0.198 10 false ADPG 5.927,1.26 6.542,1.458 0.615,0.198 10 false VAR+ 5.917,1.781 6.531,1.979 0.615,0.198 10 false VAL+ 5.917,2.25 6.531,2.448 0.615,0.198 10 false VA- 5.927,2.677 6.542,2.875 0.615,0.198 10 false AGND 5.875,3.125 6.49,3.323 0.615,0.198 10 false G152 5.885,3.292 7.125,3.635 1.24,0.344 10 false Navigation Receiver Assembly 1.323,1.156 1.677,1.354 0.354,0.198 10 false 7 1.323,1.615 1.677,1.813 0.354,0.198 10 false 8 1.333,2.104 1.688,2.302 0.354,0.198 10 false 9 1.313,2.594 1.667,2.792 0.354,0.198 10 false 12 4.083,2.896 4.698,3.094 0.615,0.198 10 false Shielded 5.646,0.688 5.865,0.865 0.219,0.177 10 false 25 5.646,1.167 5.865,1.344 0.219,0.177 10 false 26 5.635,1.646 5.854,1.823 0.219,0.177 10 false 28 5.646,2.104 5.865,2.281 0.219,0.177 10 false 27 5.646,2.604 5.865,2.781 0.219,0.177 10 false 11 0.833,0.792 1.448,0.99 0.615,0.198 10 false ADPG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the z8 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-25 (ADPG) - z8-10 (ADPG) Always Below 1 Ω
G152-26 (VAR+) - z8-7 (VAR+) Always Below 1 Ω
G152-28 (VAL+) - z8-8 (VAL+) Always Below 1 Ω
G152-27 (VA-) - z8-9 (VA-) Always Below 1 Ω
G152-11 (AGND) - z8-12 (AGND) Always Below 1 Ω
G152-25 (ADPG) - Body ground Always 10 kΩ or higher
G152-26 (VAR+) - Body ground Always 10 kΩ or higher
G152-28 (VAL+) - Body ground Always 10 kΩ or higher
G152-27 (VA-) - Body ground Always 10 kΩ or higher
G152-11 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR