Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

·

The navigation receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the navigation receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.


WIRING DIAGRAM

E278095
0.688,1.563 1.406,2.094 0.719,0.531 10 false Telephone Microphone Assembly 1.563,1.188 2.083,1.375 0.521,0.188 10 false MACC 1.594,1.677 2.115,1.865 0.521,0.188 10 false MCO+ 1.625,2.146 2.146,2.333 0.521,0.188 10 false MCO- 2.083,1.188 2.604,1.375 0.521,0.188 10 false 4 2.083,1.656 2.604,1.844 0.521,0.188 10 false 3 2.073,2.125 2.594,2.313 0.521,0.188 10 false 2 2.99,2.906 3.75,3.104 0.76,0.198 10 false Shielded 4.521,2.896 5.281,3.094 0.76,0.198 10 false Shielded 5.771,1.167 6.281,1.365 0.51,0.198 10 false 4 5.76,1.646 6.271,1.844 0.51,0.198 10 false 5 5.708,2.125 6.219,2.323 0.51,0.198 10 false 19 5.719,2.635 6.229,2.833 0.51,0.198 10 false 18 5.979,1.281 6.49,1.479 0.51,0.198 10 false MACC 5.969,1.771 6.479,1.969 0.51,0.198 10 false MIN+ 5.969,2.25 6.479,2.448 0.51,0.198 10 false MIN- 5.969,2.698 6.479,2.896 0.51,0.198 10 false SGND 5.813,3.365 6.323,3.563 0.51,0.198 10 false G152 5.823,3.521 7.063,3.844 1.24,0.323 10 false Navigation Receiver Assembly 0.469,3.375 0.979,3.573 0.51,0.198 10 false N2 0.469,3.542 2,3.75 1.531,0.208 10 false Map Light Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the N2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-4 (MACC) - N2-4 (MACC) Always Below 1 Ω
G152-5 (MIN+) - N2-3 (MCO+) Always Below 1 Ω
G152-19 (MIN-) - N2-2 (MCO-) Always Below 1 Ω
G152-4 (MACC) - Body ground Always 10 kΩ or higher
G152-5 (MIN+) - Body ground Always 10 kΩ or higher
G152-19 (MIN-) - Body ground Always 10 kΩ or higher
G152-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E237416
1.448,0.448 1.979,0.688 0.531,0.24 2.208,1.75 2.469,0.875 2.469,0.875 2.719,0.875 true 2.219,2 2.552,2.49 2.552,2.49 2.802,2.49 true 2.417,2.75 2.167,2.75 2.167,2.75 2.083,2.01 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.563,0.479 2,0.698 0.438,0.219 10 false G152 2.75,0.781 3.25,1.01 0.5,0.229 10 false MACC 2.833,2.406 3.302,2.583 0.469,0.177 10 false SGND 2.458,2.667 2.792,2.906 0.333,0.24 10 false MIN-
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-18 (SGND) - Body ground Always Below 1 Ω
G152-19 (MIN-) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G152-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

3.CHECK MAP LIGHT ASSEMBLY

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

3.CHECK MAP LIGHT ASSEMBLY
a.
E244515
1.458,0.813 1.938,1.073 0.479,0.26 2.281,2.625 1.969,1.979 true 1.063,2.573 1.75,1.948 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.604,0.875 1.917,1.073 0.313,0.198 10 false N2 0.594,2.49 1.042,2.677 0.448,0.188 10 false MCO+ 2.198,2.656 2.656,2.875 0.458,0.219 10 false MCO-
*a Component with harness connected
(Map Light Assembly)


Turn the ignition switch to ACC.


b.

Connect an oscilloscope to terminals 3 (MCO+) and 2 (MCO-) of the map light assembly connector.


c.

Check the waveform of the telephone microphone assembly using the oscilloscope.


Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is output A
A waveform synchronized with the voice input to the map light assembly is not output B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Check if the same problem occurs again.


Result:
Proceed to
Malfunction disappears
Malfunction does not disappear



Malfunction disappears

END (TELEPHONE MICROPHONE IS DEFECTIVE)

Malfunction does not disappear

5.CHECK MAP LIGHT ASSEMBLY
5.CHECK MAP LIGHT ASSEMBLY
a.

Replace the map light assembly with a new or normally functioning one.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Check if the same problem occurs again.


Result:
Proceed to
Malfunction disappears
Malfunction does not disappear



Malfunction disappears

END (MAP LIGHT ASSEMBLY IS DEFECTIVE)

Malfunction does not disappear

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE