Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052656 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

Using this circuit, the radio receiver assembly sends power to the telephone microhpone assembly, and the telephone microphone assembly sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM

E277658
5.885,0.604 6.5,0.802 0.615,0.198 10 false MACC 5.885,1.083 6.5,1.281 0.615,0.198 10 false MIN+ 5.885,1.563 6.5,1.76 0.615,0.198 10 false MIN- 5.885,2.031 6.5,2.229 0.615,0.198 10 false SGND 5.885,2.51 6.5,2.708 0.615,0.198 10 false SNS2 5.688,0.5 6.302,0.698 0.615,0.198 10 false 4 5.688,0.969 6.302,1.167 0.615,0.198 10 false 5 5.615,1.448 6.229,1.646 0.615,0.198 10 false 19 5.635,1.906 6.25,2.104 0.615,0.198 10 false 18 5.667,2.385 6.281,2.583 0.615,0.198 10 false 6 5.833,2.917 6.448,3.115 0.615,0.198 10 false G1 5.823,3.083 6.792,3.51 0.969,0.427 10 false Radio Receiver Assembly 4.604,2.167 5.438,2.365 0.833,0.198 10 false Shielded 3.417,2.167 4.25,2.365 0.833,0.198 10 false Shielded 1.823,0.5 2.438,0.698 0.615,0.198 10 false MACC 1.854,0.969 2.469,1.167 0.615,0.198 10 false MCO+ 1.875,1.448 2.49,1.646 0.615,0.198 10 false MCO- 2.385,0.5 3,0.698 0.615,0.198 10 false 4 2.385,0.958 3,1.156 0.615,0.198 10 false 3 2.385,1.417 3,1.615 0.615,0.198 10 false 2 0.458,1.865 1.958,2.198 1.5,0.333 10 false Telephone Microphone Assembly 0.813,2.604 1.427,2.802 0.615,0.198 10 false N2 0.813,2.771 2.813,3.021 2,0.25 10 false Map Light Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G1 radio receiver assembly connector.


b.

Disconnect the N2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-6 (SNS2) - Body ground Always Below 1 Ω
G1-4 (MACC) - N2-4 (MACC) Always Below 1 Ω
G1-5 (MIN+) - N2-3 (MCO+) Always Below 1 Ω
G1-19 (MIN-) - N2-2 (MCO-) Always Below 1 Ω
G1-4 (MACC) - Body ground Always 10 kΩ or higher
G1-5 (MIN+) - Body ground Always 10 kΩ or higher
G1-19 (MIN-) - Body ground Always 10 kΩ or higher
G1-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO RECEIVER ASSEMBLY
a.
E237416
1.448,0.448 1.865,0.677 0.417,0.229 2.208,1.75 2.469,0.875 2.469,0.875 2.719,0.875 true 2.219,2 2.552,2.49 2.552,2.49 2.802,2.49 true 2.417,2.75 2.167,2.75 2.167,2.75 2.083,2.01 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.563,0.479 1.875,0.677 0.313,0.198 10 false G1 2.75,0.781 3.25,1.01 0.5,0.229 10 false MACC 2.833,2.406 3.302,2.583 0.469,0.177 10 false SGND 2.458,2.667 2.792,2.906 0.333,0.24 10 false MIN-
*a Component with harness connected
(Radio Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-18 (SGND) - Body ground Always Below 1 Ω
G1-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

3.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Check that the malfunction disappears.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAP LIGHT ASSEMBLY