Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USBB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E278688
6.125,0.427 6.74,0.625 0.615,0.198 10 false USV1 5.865,0.292 6.031,0.5 0.167,0.208 10 false 1 6.125,0.854 6.74,1.052 0.615,0.198 10 false US1- 5.885,0.75 6.052,0.958 0.167,0.208 10 false 2 6.125,1.302 6.74,1.5 0.615,0.198 10 false US1+ 5.875,1.198 6.042,1.406 0.167,0.208 10 false 3 6.125,1.74 6.74,1.938 0.615,0.198 10 false UGD1 5.885,1.625 6.052,1.833 0.167,0.208 10 false 4 6.115,2.167 6.729,2.365 0.615,0.198 10 false USG1 5.885,2.042 6.052,2.25 0.167,0.208 10 false 5 0.646,0.417 1.26,0.615 0.615,0.198 10 false USV1 1.198,0.302 1.365,0.51 0.167,0.208 10 false 1 0.688,0.854 1.302,1.052 0.615,0.198 10 false US1- 1.219,0.75 1.385,0.958 0.167,0.208 10 false 2 0.656,1.302 1.271,1.5 0.615,0.198 10 false US1+ 1.208,1.188 1.375,1.396 0.167,0.208 10 false 3 0.635,1.729 1.25,1.927 0.615,0.198 10 false UGD1 1.219,1.625 1.385,1.833 0.167,0.208 10 false 4 0.708,2.177 1.323,2.375 0.615,0.198 10 false UJSS 1.219,2.063 1.385,2.271 0.167,0.208 10 false 5 3.323,2.313 3.938,2.51 0.615,0.198 10 false Shielded 5.802,2.51 6.417,2.708 0.615,0.198 10 false z9 5.802,2.688 7,3.104 1.198,0.417 10 false Radio and Display Receiver Assembly 0.219,2.49 0.833,2.688 0.615,0.198 10 false z8 0.219,2.667 1.375,3.125 1.156,0.458 10 false No. 1 Stereo Jack Adapter Assembly

CAUTION / NOTICE / HINT

HINT:
·

For vehicles equipped with an Extension Module, refer to optional equipment's manuals.

·

When a large amount of data is in a USB device, it may take a while to before play begins.

·

When using a USB device, files that are copy protected or encrypted cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>SYSTEM DESCRIPTION



Result:
Result Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B



A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the z9 radio and display receiver assembly connector.


b.

Disconnect the z8 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-1 (USV1) - z8-1 (USV1) Always Below 1 Ω
z9-2 (US1-) - z8-2 (US1-)
z9-3 (US1+) - z8-3 (US1+)
z9-4 (UGD1) - z8-4 (UGD1)
z9-5 (USG1) - z8-5 (UJSS)
z9-1 (USV1) - Body ground Always 10 kΩ or higher
z9-2 (US1-) - Body ground
z9-3 (US1+) - Body ground
z9-4 (UGD1) - Body ground
z9-5 (USG1) - Body ground



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.
E278189
0.563,0.896 1.021,1.146 0.458,0.25 0.875,0.5 1.125,0.5 1.125,0.5 1.49,0.875 true 2.583,0.5 2.333,0.5 2.333,0.5 1.917,0.875 true 0.667,0.938 1.01,1.156 0.344,0.219 10 false z8 0.052,0.052 0.396,0.271 0.344,0.219 10 false *a 0.479,0.427 0.917,0.594 0.438,0.167 10 false USV1 2.625,0.417 3.125,0.667 0.5,0.25 10 false UGD1
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Reconnect the z9 radio and display receiver assembly connector.


b.

Disconnect the No. 1 stereo jack adapter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z8-1 (USV1) - z8-4 (UGD1) Ignition switch ACC 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/ restore it.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Make sure that back up music data is available before performing this operation.



b.

Save the data again and check if it can be played on the in-vehicle device.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (USB OR "iPod" IS DEFECTIVE)

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>SYSTEM DESCRIPTION




Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if USB device or "iPod" is recognized by radio and display receiver assembly, or if information such as track, artist and album names are displayed on screen.

OK:

USB device or "iPod" is recognized or track information such as track, artist and album names are displayed.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG