Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends an external device sound signal to the radio and display receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

E278677
5.667,0.406 6.281,0.604 0.615,0.198 10 false VAL+ 5.375,0.302 5.667,0.5 0.292,0.198 10 false 28 5.667,0.917 6.281,1.115 0.615,0.198 10 false VAR+ 5.375,0.802 5.667,1 0.292,0.198 10 false 26 5.667,1.417 6.281,1.615 0.615,0.198 10 false VA- 5.375,1.313 5.667,1.51 0.292,0.198 10 false 27 5.667,1.917 6.281,2.115 0.615,0.198 10 false AGND 5.375,1.802 5.667,2 0.292,0.198 10 false 11 5.667,2.427 6.281,2.625 0.615,0.198 10 false ADPG 5.375,2.302 5.667,2.5 0.292,0.198 10 false 25 4,2.083 4.615,2.281 0.615,0.198 10 false Shielded 2.615,2.083 3.229,2.281 0.615,0.198 10 false Shielded 1.198,0.417 1.813,0.615 0.615,0.198 10 false VAL+ 1.156,0.917 1.771,1.115 0.615,0.198 10 false VAR+ 1.271,1.427 1.885,1.625 0.615,0.198 10 false VA- 1.167,1.938 1.781,2.135 0.615,0.198 10 false AGND 1.146,2.438 1.76,2.635 0.615,0.198 10 false ADPG 1.656,0.292 1.948,0.49 0.292,0.198 10 false 7 1.667,0.802 1.958,1 0.292,0.198 10 false 6 1.667,1.313 1.958,1.51 0.292,0.198 10 false 8 1.667,1.823 1.958,2.021 0.292,0.198 10 false 11 1.667,2.313 1.958,2.51 0.292,0.198 10 false 10 0.583,2.833 0.979,3.042 0.396,0.208 10 false z8 0.594,3.021 1.771,3.385 1.177,0.365 10 false No. 1 Stereo Jack Adapter Assembly 5.542,2.833 6.083,3 0.542,0.167 10 false G127 5.552,3 6.76,3.458 1.208,0.458 10 false Radio and Display Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - STEREO JACK ADAPTER)
a.

Disconnect the G127 radio and display receiver assembly connector.


b.

Disconnect the z8 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-28 (VAL+) - z8-7 (VAL+) Always Below 1 Ω
G127-26 (VAR+) - z8-6 (VAR+)
G127-27 (VA-) - z8-8 (VA-)
G127-11 (AGND) - z8-11 (AGND)
G127-25 (ADPG) - z8-10 (ADPG)
G127-28 (VAL+) - Body ground Always 10 kΩ or higher
G127-26 (VAR+) - Body ground
G127-27 (VA-) - Body ground
G127-11 (AGND) - Body ground
G127-25 (ADPG) - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR