1. LEARNING VALUES CONFIRMATION
This procedure uses the GTS to display the learned value (crank time compensation learning value) stored in the ECM.
A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Learning values confirmation.
| Tester Display |
|---|
| Learning Values Confirmation |
Press "Next".
Press "Next" again to proceed.
Select the value to confirm and press "Next".
When the next screen is displayed, confirm the contents and press "Exit".
2. LEARNING VALUES SAVE
This procedure uses the GTS to save the learned value stored in the ECM in the GTS depending on the components being replaced.
When replacing the engine assembly or the injector assembly together with the ECM, this function automatically determines the data which can be transferred (old data) and saves the data in the GTS.
When there is no data to read from the ECM, manually perform the procedure to register each compensation code and learning value in the ECM.
A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Learning values save.
| Tester Display |
|---|
| Learning Values Save |
Press "Next".
Press "Next" again to proceed.
Select any components being replaced and press "Next". If no applicable components are displayed, press "Next" without selecting anything.
If the overwrite confirmation screen is displayed, press "Overwrite".
When the operation is finished, confirm the date and time of the save operation, and press "Exit".
3. LEARNING VALUES WRITE
This procedure uses the GTS to write the learned value stored in the GTS to the ECM.
A malfunction may occur when writing the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Learning values write.
| Tester Display |
|---|
| Learning Values Write |
Press "Next".
Press "Next" again to proceed.
If the "Error Learning Values Write" screen indicating a problem with the saved value(s) or that there are no saved values is displayed, perform "Learning Values Save" again.
Confirm the date and time of the save operation, and then press "Yes".
Confirm the contents, and then press "Next".
If any instructions are displayed on the GTS, manually perform the procedure to register each applicable compensation code or learning value in the ECM.
Clear the DTCs.
4. DESCRIPTION OF VIN
The Vehicle Identification Number (VIN) must be input into the replacement ECM.
The VIN is a 17-digit alphanumeric number. The GTS is required to register the VIN.
This registration section consists of two parts, Read VIN and Write VIN.
Read VIN: Explains the VIN reading process in a flowchart. This process allows the VIN stored in the ECM to be read, in order to confirm that the two VINs, provided with the vehicle and stored in the vehicle's ECM, are the same.
Write VIN: Explains the VIN writing process in a flowchart. This process allows the VIN to be input into the ECM. If the ECM is changed, or the ECM VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.
5. READ VIN
Confirm the vehicle VIN.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / VIN / VIN Read.
| Tester Display |
|---|
| VIN |
6. WRITE VIN
Confirm the vehicle VIN.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / VIN / VIN Write.
| Tester Display |
|---|
| VIN |