Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2014.10
RM1840EF _58 Vehicle Interior _009645 SUPPLEMENTAL RESTRAINT SYSTEMS _0052709 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Passenger Side Pretensioner Squib Circuit  B1906/74  Open in Front Passenger Side Pretensioner Squib Circuit  B1907/74  Short to GND in Front Passenger Side Pretensioner Squib Circuit  B1908/74  Short to B+ in Front Passenger Side Pretensioner Squib Circuit  


DESCRIPTION

The front pretensioner circuit consists of the center airbag sensor and front seat outer belt assembly RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front seat outer belt assembly RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the front seat outer belt assembly RH circuit during the primary check.

·

A front seat outer belt assembly RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly RH

·

Center airbag sensor assembly


DTC is output in check mode
B1906/74 Open in Front Passenger Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the front seat outer belt assembly RH circuit for 2 seconds.

·

A front seat outer belt assembly RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly RH

·

Center airbag sensor assembly


DTC is output in check mode
B1907/74 Short to GND in Front Passenger Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the front seat outer belt assembly RH circuit for 0.5 seconds.

·

A front seat outer belt assembly RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly RH

·

Center airbag sensor assembly


DTC is output in check mode
B1908/74 Short to B+ in Front Passenger Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the front seat outer belt assembly RH circuit for 0.5 seconds.

·

A front seat outer belt assembly RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly RH

·

Center airbag sensor assembly


DTC is output in check mode

WIRING DIAGRAM

C247622E37
0.74,3.208 3.083,3.438 2.344,0.229 10 false Front Seat Outer Belt Assembly RH 2.188,1.552 2.406,1.74 0.219,0.188 10 false R+ 2.208,2.385 2.385,2.573 0.177,0.188 10 false R- 4.792,1.677 5.188,1.865 0.396,0.188 10 false PP+ 4.792,2.521 5.188,2.708 0.396,0.188 10 false PP- 2.479,1.552 2.625,1.719 0.146,0.167 10 false 1 2.49,2.385 2.646,2.542 0.156,0.156 10 false 2 4.573,1.552 4.688,1.719 0.115,0.167 10 false 4 4.573,2.406 4.698,2.573 0.125,0.167 10 false 5 4.76,4.167 5.083,4.354 0.323,0.188 10 false K39 4.75,4.323 6.198,4.531 1.448,0.208 10 false Center Airbag Sensor 0.74,3.052 1.208,3.208 0.469,0.156 10 false K45

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH
a.
C301867C04
0.198,1.99 0.604,2.25 0.406,0.26 2.198,2.208 2.438,2.208 false 0.813,0.75 1.125,0.948 0.313,0.198 10 false *1 1.76,0.969 2.073,1.167 0.313,0.198 10 false A 1.656,1.281 1.969,1.479 0.313,0.198 10 false *2 1.188,1.281 1.5,1.479 0.313,0.198 10 false C 1,1.281 1.313,1.479 0.313,0.198 10 false D 0.802,1.635 1.115,1.833 0.313,0.198 10 false *a 0.292,2.042 0.604,2.24 0.313,0.198 10 false K45 2.458,1.667 2.771,1.865 0.313,0.198 10 false *3 2.49,2.125 2.802,2.323 0.313,0.198 10 false *4
*1 Front Seat Outer Belt Assembly RH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt assembly RH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.


Result:
Proceed to
OK
NG



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.



OK

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor.


b.
C208250C05
0.625,1.094 0.938,1.292 0.313,0.198 10 false *1 1.26,1.094 1.573,1.292 0.313,0.198 10 false *2 1.729,1.698 2.042,1.896 0.313,0.198 10 false *3 0.865,1.615 1.021,1.813 0.156,0.198 10 false D 1.083,1.615 1.24,1.813 0.156,0.198 10 false C 1.49,1.615 1.646,1.813 0.156,0.198 10 false B 1.906,1.333 2.063,1.531 0.156,0.198 10 false A
*1 Front Seat Outer Belt Assembly RH
*2 Floor Wire
*3 Center Airbag Sensor


Check that the connectors (on the center airbag sensor side and front seat outer belt assembly RH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
a.
C301866C01
0.406,1.948 0.781,2.188 0.375,0.24 1.125,2.615 1.542,2.198 true 2.26,2.635 1.74,2.198 true 0.656,0.698 0.969,0.896 0.313,0.198 10 false *1 1.208,0.708 1.521,0.906 0.313,0.198 10 false *2 1.823,0.917 2.135,1.115 0.313,0.198 10 false A 1.406,1.208 1.719,1.406 0.313,0.198 10 false B 1.021,1.198 1.333,1.396 0.313,0.198 10 false C 0.813,1.198 1.125,1.396 0.313,0.198 10 false D 1.76,1.26 2.073,1.458 0.313,0.198 10 false *3 1.573,1.552 1.885,1.75 0.313,0.198 10 false *a 0.469,1.979 0.781,2.177 0.313,0.198 10 false K45 2.344,2.021 2.656,2.219 0.313,0.198 10 false *4 2.323,2.604 2.635,2.802 0.313,0.198 10 false R- 0.885,2.615 1.198,2.813 0.313,0.198 10 false R+
*1 Front Seat Outer Belt Assembly RH
*2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K45-1 (R+) - Body ground Ignition switch ON Below 1 V
K45-2 (R-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K45-1 (R+) - K45-2 (R-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K45-1 (R+) - K45-2 (R-) Always 1 MΩ or higher
K45-1 (R+) - Body ground Always 1 MΩ or higher
K45-2 (R-) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C146261C23
0.823,1.115 0.823,1.5 false 0.76,1.521 0.958,1.719 0.198,0.198 10 false *1 0.979,1.219 1.104,1.417 0.125,0.198 10 false D 1.104,1.219 1.25,1.406 0.146,0.188 10 false C 1.479,1.521 1.677,1.688 0.198,0.167 10 false *2 1.646,0.969 1.792,1.156 0.146,0.188 10 false A
*1 Front Seat Outer Belt Assembly RH
*2 Center Airbag Sensor


Connect the connectors to the front seat outer belt assembly RH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG