ECD SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
The main components of the engine control system are as follows:
| Component | Outline | Quantity | Function |
| ECM | 32-bit CPU | 1 | The ECM effects overall control of the engine control system to suit the operating conditions of the engine in accordance with the signals provided by the sensors. |
| Injector Driver | DC/DC Converter | 1 | The injector driver is used to drive the injector at high speeds. The injector driver has achieved high-speed driving under high fuel pressure conditions through the use of a DC/DC converter that provides a high voltage, quick-charging system. |
| Turbo Pressure Sensor | Semiconductor Silicon Chip Type | 1 | This sensor uses built-in semiconductors to detect the intake manifold pressure. |
| Atmospheric Pressure Sensor | Semiconductor Silicon Chip Type | 1 | This sensor, which is built into the ECM, uses semiconductors to detect the atmospheric pressure. |
| Fuel Pressure Sensor | Semiconductor Strain Gauge Type | 1 | This sensor uses built-in semiconductors to detect the internal pressure of the common-rail. |
| Pressure Discharge Valve | Solenoid Type | 1 | The pressure discharge valve regulates the fuel pressure. |
| Crank Position Sensor | Pick-up Coil Type (Rotor Teeth/36-2) | 1 | This sensor detects the engine speed and performs the cylinder identification. |
| Camshaft Position Sensor | Pick-up Coil Type (Rotor Teeth/5) | 1 | This sensor performs the cylinder identification. |
| Intake Mass Air Flow Meter Sub-assembly | Hot-wire Type | 1 | This sensor uses a built-in hot-wire to directly detect the intake air mass. |
| Intake Air Temperature Sensor (Built into Intake Mass Air Flow Meter Sub-assembly) | Thermistor Type | 1 | This sensor detects the intake air temperature by means of an internal thermistor. |
| Engine Coolant Temperature Sensor | Thermistor Type | 1 | This sensor detects the engine coolant temperature by means of an internal thermistor. |
| Fuel Temperature Sensor | Thermistor Type | 1 | This sensor detects the fuel temperature in the supply pump by means of an internal thermistor. |
| Throttle Position Sensor | Non-contact Type | 1 | This sensor detects the diesel throttle valve opening angle. |
| Accelerator Pedal Position Sensor | Non-contact Type | 1 | This sensor detects the amount of pedal effort applied to the accelerator pedal. |
| Suction Control Valve (SCV) | Linear Solenoid Valve | 1 | The SCV position is controlled by the signals from the ECM, and a fuel volume that suits the SCV position is drawn into the pumping portion (plunger portion). |
| Injector Assembly | 6-hole, Solenoid Type | 4 | The injector injects the fuel to the combustion chamber in accordance with the ECM signals via the injector driver. |
| SYSTEM CONTROL |
The engine control system has the following features. The ECM controls these systems:
| System | Outline | |
| Fuel Injection Volume Control | Based on the signals received from the sensors, the ECM determines the fuel injection volume in accordance with the engine condition. | |
| Fuel Injection Timing Control | Based on the signals received from the sensors, the ECM determines the fuel injection timing in accordance with the engine condition. | |
| During Starting Control | To facilitate startability, the ECM optimally controls the injection volume and injection timing during starting. | |
| Idle Speed Control | The ECM determines the idle speed in accordance with the engine condition, and controls the fuel injection volume in order to maintain the target idle speed. | |
| Fuel Pressure Control | Based on the signals received from the sensors, the ECM controls fuel pressure using the Suction Control Valve (SCV) and pressure discharge valve in accordance with engine operating conditions. | |
| Pilot Injection Control | Based on the signals received from the sensors, the ECM determines pilot injection volume/timing and interval (between pilot injection and main injection) in accordance with the engine condition. | |
| Glow Plug Control | The ECM controls the length of time for which the current is applied to the glow plug assemblies, in accordance with the engine coolant temperature. | |
| Diesel Throttle Control |
| |
| Air Conditioning Cut-off Control | By controlling the air conditioning compressor on or off in accordance with the engine condition, driveability is maintained. | |
| Diagnosis | When the ECM detects a malfunction, it diagnoses and memorizes the failed section. | |
| Fail-safe | When the ECM detects a malfunction, it stops or controls the engine in accordance with the data already stored in the memory. | |
| FUNCTION |
Fuel Injection Volume Control
The ECM calculates 2 types of values: the basic injection volume and the maximum injection volume. Then, the ECM compares the basic and maximum injection volumes, and determines the smaller calculated value to be the final injection volume.



Fuel Injection Timing Control
Fuel injection timing is controlled as shown below:

During Starting Control
The starting injection volume is determined by adjusting the basic injection volume in accordance with the starter on signals (on time), engine coolant temperature sensor signals and engine speed signal. When the engine is cold, the engine coolant temperature will be lower and the injection volume will be greater.

To determine the starting injection timing, the target injection timing is corrected in accordance with the starter signals, engine coolant temperature, and engine speed. When the engine coolant temperature is low, if the engine speed is high, the injection timing is advanced.

Idle Speed Control
Idle speed control correction is controlled as shown below:

Fuel Pressure Control
The ECM calculates the target injection pressure (32 MPa to 160 MPa) based on the signals from the accelerator pedal position sensor and the crank position sensor. To control fuel pressure, signals sent to the Suction Control Valve (SCV) of the supply pump assembly regulate the suction volume, and signals sent to the pressure discharge valve of the common-rail regulate the discharge volume, so that the pressure detected by the fuel pressure sensor matches the target injection pressure.

Pilot Injection Control
Pilot injection is a method that provides an auxiliary fuel injection before the main fuel injection takes place. The purpose of pilot injection is to gently start the combustion of the fuel of the main injection in order to reduce combustion noise.
| State | Pilot Injection | Ordinary Injection |
| Fuel Injection | ![]() | ![]() |
| Combustion Pressure | ![]() | ![]() |
During pilot injection, the pilot injection volume, timing, and interval (between pilot injection and main injection) are controlled as shown below:

Glow Plug Control
The ECM controls the length of time for which the current is applied to the glow plug relay when the engine starts in accordance with engine coolant temperature to control the length of time for which the current is applied to the glow plug assemblies.
Diesel Throttle Control
The ECM controls the opening of the diesel throttle valve to reduce the noise caused when idling and decelerating, and the noise and vibrations caused when stopping the engine.
| CONSTRUCTION |
ECM
The 32-bit CPU of the ECM is used to increase the speed for processing the signals.
On the models with automatic transmission, the ECM maintains communication with a separate, independent TCM through Controller Area Network (CAN). Thus, engine control is effected in coordination with ECT control.
Injector Driver
The injector driver is used to drive the injector at high speeds. The injector driver has achieved high-speed driving under high fuel pressure conditions through the use of a DC/DC converter that provides a high voltage, quick-charging system.
The ECM constantly monitors the injector driver and stops the engine when an abnormal condition is detected.
Turbo Pressure Sensor
The turbo pressure sensor consists of a semiconductor which utilizes the characteristics of a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the intake air pressure into an electrical signal, and sends it to the ECM in an amplified form.

Fuel Pressure Sensor
The fuel pressure sensor, which is mounted on the common-rail, outputs a signal that represents the fuel pressure in the common-rail to the ECM in order to constantly regulate the fuel at an optimal pressure.
The fuel pressure sensor consists of a semiconductor which utilizes the characteristics of a silicon chip that changes its electrical resistance when pressure is applied to it.
The fuel pressure sensor has 2 circuits (main and sub), which enable the ECM to constantly compare the values detected by the 2 circuits. As a result, highly precise values can be detected, which also enables a higher level of fail-safe control.

Pressure Discharge Valve
The pressure discharge valve regulates the fuel pressure. In the pressure discharge valve, the plunger opens and closes in accordance with the actuation signals from the injector driver. Thus, it regulates pressure by releasing excess pressure from the common-rail. In addition, it has a pressure reduction function in case of emergency.

| *1 | Common-rail Assembly | *2 | Pressure Discharge Valve |
| *3 | Plunger | - | - |
| *a | Pressure Discharge Valve Cross Section | - | - |
![]() | Fuel from Common-rail (High Pressure) | ![]() | Fuel to Fuel Tank (Excess Pressure) |
Crank Position Sensor and Camshaft Position Sensor
The timing rotor of the crankshaft consists of 34 teeth, with 2 teeth missing. The crank position sensor outputs the crankshaft rotation signals every 10°, and the missing teeth are used to determine the top dead center.
To detect the camshaft position, a protrusion that is provided on the timing pulley is used to generate 5 pulses for every 2 revolutions of the crankshaft.

Intake Mass Air Flow Meter Sub-assembly
This engine uses the hot-wire type air flow meter designed for direct electrical measurement of the intake air mass flow.
This intake mass air flow meter sub-assembly has a built-in intake air temperature sensor.

| *1 | Intake Mass Air Flow Meter Sub-assembly | *2 | Temperature Sensing Element |
| *3 | Platinum Hot-wire Element | *4 | Intake Air Temperature Sensor |
![]() | Air Flow | - | - |
Throttle Position Sensor
The throttle position sensor is mounted on the diesel throttle body assembly. To detect the opening angle of the diesel throttle valve, the throttle position sensor converts the magnetic flux density, that changes when the magnetic yoke (located on the same axis as the diesel throttle valve shaft) rotates around the Hall IC, into electric signals to operate the throttle control motor.

Accelerator Pedal Position Sensor
The magnetic yoke that is mounted at the base of the accelerator pedal arm moves around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur at that time into electrical signals, and outputs them in the form of accelerator pedal effort to the ECM.

| OPERATION |
Glow Plug Control
When the ignition switch is turned from off to ON, the ECM operates the glow plug relay to heat the glow plug assemblies rapidly. At that moment, the glow indicator light in the combination meter assembly is illuminated to inform the driver that the glow plug assemblies are being heated.
When the engine starts and the starter signal is off, after-glow control is conducted. When the temperature of the glow plug assembly reaches a predetermined level during after-glow control, it is maintained at a nearly constant level using the self-temperature-controlling function of the glow plug assembly.

Diesel Throttle Control
The opening of the diesel throttle valve is controlled by the ECM in accordance with the engine conditions. As a result, the noise that is generated during idling and deceleration, as well as the noise and vibrations that are generated when the engine is stopped, have been reduced and this control makes it possible to recirculate the exhaust gas in accordance with the driving conditions.

| *1 | Throttle Position Sensor | *2 | Throttle Control Motor |
| *3 | Diesel Throttle Valve | *4 | ECM |
| *5 | Engine Speed Signal | *6 | Vehicle Speed Signal |
| *7 | Engine Coolant Temperature Signal | *8 | Intake Air Temperature Signal |
| *9 | Accelerator Pedal Position Signal | *10 | Intake Air Pressure Signal |
| *11 | Ignition Signal | - | - |