FUEL SYSTEM > DETAILS |
| SYSTEM CONTROL |
Common-rail System
In this system, the highly pressurized fuel supplied by the supply pump is stored in the common-rail, and the ECM sends signals to the injectors via the injector driver in order to control the injection timing and injection volume.

| *1 | Fuel Pressure Sensor | *2 | Common-rail Assembly |
| *3 | Pressure Discharge Valve | *4 | Supply Pump Assembly |
| *5 | Fuel Temperature Sensor | *6 | Suction Control Valve (SCV) |
| *7 | Injector Assembly | *8 | Fuel Filter Assembly |
| *9 | Fuel Tank | *10 | Injector Driver |
| *11 | ECM | *12 | Crank Position Sensor (NE Signal) |
| *13 | Camshaft Position Sensor (G Signal) | - | - |
| *a | Fuel (Suction) | *b | Fuel (Return) |
| *c | Fuel (High Pressure) | - | - |
| CONSTRUCTION |
Supply Pump Assembly
An HP3 type supply pump is used.

| Type | HP3 | |
| Length | A | 190.2 mm (7.49 in.) |
| B | 129.0 mm (5.08 in.) | |
| SCV | 1 | |
| Plunger | φ 8.5 mm x 2 | |
| Weight | 3800 g (8.38 lb) | |
The supply pump consists of an eccentric camshaft, a ring cam, 2 plungers, 4 check valves, a Suction Control Valve (SCV), a fuel temperature sensor, and a feed pump.
The 2 plungers are placed opposite each other outside of the ring cam.

| *1 | Check Valve (for Suction) | *2 | Plunger |
| *3 | Eccentric Camshaft | *4 | Ring Cam |
| *5 | Check Valve (for Discharge) | *6 | Feed Pump |
| *7 | Fuel Temperature Sensor | *8 | SCV |
| *9 | Eccentric Cam Portion | - | - |
| *a | From Fuel Tank (for Suction) | *b | To Fuel Tank (for Return) |
| *c | To Common-rail | - | - |
Common-rail Assembly
The function of the common-rail is to store the fuel that has been pressurized by the supply pump.
The common-rail is provided with a fuel pressure sensor and pressure discharge valve.
The fuel pressure sensor detects the fuel pressure in the common-rail.
The pressure discharge valve regulates the fuel pressure. In the pressure discharge valve, the plunger opens and closes in accordance with the actuation signals from the injector driver. Thus, it regulates pressure by releasing excess pressure from the common-rail. In addition, it has a pressure reduction function in case of emergency.
Internally, the common-rail contains a main hole and 5 branch holes that intersect the main hole. Each branch hole functions as an orifice that dampens the fluctuation of the fuel pressure.

| *1 | Common-rail Assembly | *2 | Fuel Pressure Sensor |
| *3 | Pressure Discharge Valve | *4 | Branch Hole |
| *5 | Main Hole | - | - |
![]() | From Supply Pump | ![]() | To Injector Assembly |
![]() | To Fuel Tank (Excess Pressure) | - | - |
Injector Assembly
Each injector assembly consists of a nozzle needle, a piston, and a solenoid valve.
An injector compensation value and a Quick Response (QR) code containing encoded characteristics of the injector are printed on each injector.
The injector compensation value and QR code contain various pieces of information regarding the injector, such as model code and injection volume correction.

| *1 | Injector Assembly | *2 | Solenoid Valve |
| *3 | Piston | *4 | Nozzle Needle |
| *5 | QR Code | *6 | Injector Compensation Value |
Fuel Filter Assembly
A fuel filter assembly consists of a separate filter element and a filter housing.
A paper filter element that offers high filtering efficiency and captures the minutest particles is used.
A fuel filter warning switch is provided in the fuel filter assembly.

| *1 | Priming Pump | *2 | Fuel Filter Warning Switch (Vacuum Switch) |
| *3 | Filter Element | *4 | Filter Housing |
| *5 | Fuel Sedimenter Level Warning Switch | - | - |
| OPERATION |
Supply Pump Assembly
Due to the rotation of the eccentric cam, the ring cam pushes plunger "A" upward as illustrated below. The force of the spring pulls plunger "B" (which is located opposite plunger "A") upward. As a result, plunger "B" draws fuel in, and plunger "A" pumps fuel at the same time.

| *1 | Check Valve (for Suction) | *2 | Check Valve (for Discharge) |
| *3 | Eccentric Cam | *4 | Plunger "A" |
| *5 | Ring Cam | *6 | Plunger "B" |
| *7 | Suction Control Valve (SCV) | *8 | ECM |
The ECM controls the opening of the SCV in order to regulate the volume of fuel that is pumped by the supply pump to the common-rail. Consequently, the fuel pressure in the common-rail is controlled to the target injection pressure.
When the opening of the SCV is small, the fuel suction area is kept small, which decreases the transferable fuel quantity.
When the plunger strokes fully, however, the suction volume becomes small due to the small suction area.
Pumping will start when the fuel pressure has become higher than the common-rail pressure.

When the opening of the SCV is large, the fuel suction area is kept large, which increases the transferable fuel quantity.
If the plunger strokes fully, the suction volume will increase because the suction area is large.
Pumping will start at the time when the fuel pressure has become higher than the common-rail pressure.

Injector Assembly
When electrical current is applied to the solenoid coil, it pulls the solenoid valve up.
The orifice of the control chamber opens, allowing the fuel to flow out.
The fuel pressure in the control chamber drops.
Simultaneously, fuel flows from the orifice to the bottom of the piston and raises the piston up (to enhance response).
As a result, the piston raises the nozzle needle to inject fuel.

| *1 | Injector Assembly | *2 | Solenoid Coil |
| *3 | Solenoid Valve | *4 | Piston |
| *5 | Nozzle Needle | - | - |
| *a | Fuel from Common-rail | *b | Return Fuel |
Fuel Filter Assembly
When the water in the sedimenter section reaches a certain amount, the fuel sedimenter level warning switch comes on, the warning light in the combination meter assembly illuminates, and the multi buzzer sounds.
A fuel filter warning switch, which turns on or off when the internal vacuum of the filter increases, is provided in the fuel filter. This switch, which turns off when the internal vacuum of the fuel filter increases to a predetermined level, is connected by wire to the meter ECU.

When the meter ECU detects that the internal vacuum of the fuel filter has increased (by way of the fuel filter warning switch off signal), it determines that the fuel filter has become clogged. Then, it illuminates the fuel system warning light on the combination meter assembly to urge the driver to replace the fuel filter.
