EMISSION CONTROL SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components of the emission control system are as follows:

    Component
    Function
    Exhaust Emission System
    ECM
    Determines an optimal fuel injection volume based on the signals from various sensors.
    TWC
    Reduces CO, HC and NOx in the exhaust gas.
    Oxygen Sensor
    Detects the oxygen concentration in the exhaust emissions by measuring the electromotive force generated in the sensor itself. For details, see the 2TR-FE Engine Control.
    Air Fuel Ratio Sensor*
    Air Injection System*
    Air Pump
    Uses a built-in DC motor to supply air to the air switching valve.
    Air Switching Valve
    Introduces air that is pumped by the air pump into the exhaust manifold.
    Air Injection Control Driver
    1. Activated by the ECM, the air injection control driver actuates the electric air pump and the air switching valve.
    2. Detects an input-output circuit failure at the air injection control driver and transmits it to the ECM.
    ECM
    1. Controls the air injection system in accordance with signals from the crankshaft position sensor, engine coolant temperature sensor and intake mass air flow meter sub-assembly.
    2. Receives a failure detection signal from the air injection control driver and stores a corresponding DTC in memory.
    Evaporative Emission Control
    ECM
    Sends signals to the VSV (for EVAP) to control the purge flow.
    Charcoal Canister Sub-assembly
    Contains activated charcoal to absorb the fuel vapor created in the fuel tank.
    VSV (for EVAP)
    Opens in accordance with the signals from the ECM when the system is purging, in order to send the fuel vapor that was absorbed by the charcoal canister into the intake manifold.

    1. *: Models compliant with EURO 3 emission regulations


FUNCTION
  1. Air Injection System

    1. To ensure the proper warm-up performance of the Three-Way Catalytic converters (TWCs) after starting a cold engine, an air injection system is used.

    2. This system consists of an air pump, an air switching valve, and an air injection control driver.

    3. The ECM estimates the amount of air injected to the TWCs based on signals from the intake mass air flow meter sub-assembly in order to regulate the air injection time.


CONSTRUCTION


  1. Three-Way Catalyst (TWC)

    1. 2 TWCs have been provided in the exhaust pipe.



    2. These TWCs improve exhaust emissions by optimizing the cell density and the wall thickness.


      W105102E01


      Text in Illustration 
      *1
      TWC
      -
      -



  2. Air Pump

    1. An air pump consists of a DC motor, an impeller and an air filter.



    2. DC motor operation is controlled by the ECM via an air injection control driver. The motor supplies air into an air switching valve through the impeller.


      W102305E01


      Text in Illustration 
      *1
      Impeller
      *2
      DC Motor
      *a
      Air Pump Cross Section
      -
      -
      V100135
      To Air Switching Valve
      V100136
      From Air Inlet



  3. Air Switching Valve

    1. An air switching valve consists of an valve that switches the air flow and a reed valve that restricts the exhaust flow to one direction.

    2. The valve is a solenoid valve that is actuated by the air injection control driver.



    3. When the air switching valve turns on, an air injection pipe, which is provided in the exhaust manifold, directs the air from the air pump to the exhaust port.


      W104262E01


      Text in Illustration 
      *1
      Air Switching Valve
      *2
      Air Injection Pipe
      *3
      Exhaust Manifold
      *4
      Valve
      *5
      Reed Valve
      -
      -
      *a
      Air Switching Valve Cross Section
      -
      -
      V100135
      From Air Pump
      V100136
      To Air Injection Pipe


OPERATION


  1. Air Injection Control Driver

    1. The air injection control driver is a non-contact type relay that uses semiconductors. Activated by the ECM, this driver actuates the air pump and the air switching valve.

    2. The air injection control driver also detects failures in the input and output circuits at the air injection control driver and transmits the failure status to the ECM via duty cycle signals.



    3. For details of the control of the air injection control driver, see the following system chart:


      W102664E03


      DI Terminal Output 
      Condition
      AIRP
      AIRV
      Output (Duty Cycle Signal)
      Open circuit in line between AIDI and DI terminals.
      -
      -
      W102400E01
      Failure in line between ECM terminals and air injection control driver.
      -
      -
      W102400E01
      Output failure at air injection control driver. (Failure in air pump actuation circuit)
      -
      -
      W102402E01
      Output failure at air injection control driver. (Failure in air switching valve actuation circuit)
      -
      -
      W102403E01
      Overheat failure of air injection control driver.
      -
      -
      W102404E01
      Normal
      On
      On
      W102405E01
      Off
      Off
      W102401E01
      On
      Off
      Off
      On

  2. Evaporative Emission Control System

    1. Based on the signals from various sensors, the ECM opens and closes the VSV (for EVAP). Thus, it controls the purge flow of evaporative emissions (HC) in the charcoal canister sub-assembly in accordance with the engine conditions.