SFI SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components of the engine control system are as follows:

    Component
    Outline
    Quantity
    Function
    ECM
    32-bit CPU
    1
    The ECM optimally controls the SFI, ESA and ISC to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
    Intake Mass Air Flow Meter Sub-assembly
    Hot-wire Type
    1
    This sensor has a built-in hot-wire to directly detect the intake air mass.
    Intake Air Temperature Sensor
    Thermistor Type
    1
    This sensor detects the intake air temperature by means of an internal thermistor.
    Engine Coolant Temperature Sensor
    Thermistor Type
    1
    This sensor detects the engine coolant temperature by means of an internal thermistor.
    Crankshaft Position Sensor [Rotor Teeth]
    Pick-up Coil Type (36-2)
    1
    This sensor detects the engine speed and performs cylinder identification.
    Camshaft Position Sensor [Rotor Teeth]
    Pick-up Coil Type (3)
    1
    This sensor performs the cylinder identification.
    Accelerator Pedal Position Sensor
    Linear (Non-contact) Type
    1
    This sensor detects the amount of pedal effort applied to the accelerator pedal.
    Throttle Position Sensor
    Linear (Non-contact) Type
    1
    This sensor detects the throttle valve opening angle.
    Knock Control Sensor
    Built-in Piezoelectric Type (Non-resonant Type/Flat Type)
    1
    This sensor detects an occurrence of engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
    Air Fuel Ratio Sensor
    Heated Type (Planar Type)
    1
    As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust emissions. However, it detects the oxygen concentration in the exhaust emissions linearly.
    Oxygen Sensor
    Heated Type (Cup Type)
    1
    This sensor detects the oxygen concentration in the exhaust emissions by measuring the electromotive force which is generated in the sensor itself.
    Fuel Injector Assembly
    12-hole Type
    4
    The fuel injector assembly is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM.


SYSTEM CONTROL
  1. The engine control system has the following features. The ECM controls these systems:

    System
    Outline
    Sequential Multiport Fuel Injection (SFI)
    1. An L-type SFI system directly detects the intake air mass with a hot wire type intake mass air flow meter sub-assembly.
    2. The fuel injection system is a sequential multiport fuel injection system.
    3. Fuel injection takes two forms:
      1. Synchronous injection, which always takes place with the same timing in accordance with the basic injection duration and an additional correction based on the signals provided by the sensors.
      2. Non-synchronous injection, which takes place at the time an injection request based on the signals provided by the sensors is detected, regardless of the crankshaft position.
    1. Synchronous injection is further divided into group injection during a cold start, and independent injection after the engine is started.
    2. Injection volume correction is performed depending on the ethanol concentration of the fuel in the fuel main tank.
    Electronic Spark Advance (ESA)
    1. Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.
    2. This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends the (IGT) ignition signal to the igniter.
    3. Ignition timing correction is performed depending on the ethanol concentration of the fuel in the fuel main tank.
    Electronic Throttle Control System-intelligent (ETCS-i)
    Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort and the condition of the engine and the vehicle.
    Variable Valve Timing-intelligent (VVT-i)
    Controls the intake camshaft to an optimal valve timing in accordance with the engine condition.
    Sub-fuel System Control
    Injects the fuel which is in the fuel sub-tank during cold engine starting when the ethanol concentration of the fuel in the fuel main tank is high, and assists engine starting.
    Fuel Pump Control
    1. Fuel pump operation is controlled by signals from the ECM.
    2. The fuel pump is stopped when the Supplemental Restraint System (SRS) airbags are deployed.
    Air Conditioning Cut-off Control
    By turning the air conditioning compressor assembly on or off in accordance with the engine condition, driveability is maintained.
    Air Fuel Ratio Sensor and Oxygen Sensor Heater Control
    Maintains the temperature of the air fuel ratio sensors or oxygen sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration.
    Engine Immobiliser
    Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
    Diagnosis
    When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section.
    Fail-safe
    When the ECM detects a malfunction, the ECM stops or controls the engine in accordance with the data already stored in memory.


FUNCTION


  1. Sequential Multiport Fuel Injection (SFI)

    1. An L-type SFI system directly detects the intake air mass with a hot wire type intake mass air flow meter sub-assembly.

    2. An independent injection system (in which fuel is injected once into each cylinder for each two revolutions of the crankshaft) is used.

    3. There are two types of injections (synchronous and non-synchronous):

      1. The synchronous injection, in which corrections based on the signals from the sensors are added to the basic injection time, so that injection always occurs at the same position.
      2. The non-synchronous injection, in which injection is effected by detecting the requests from the signals of the sensors regardless of the crankshaft angle.

    4. This system performs group injection when the engine coolant temperature is extremely low and the engine speed is low.



    5. Injection volume correction is performed depending on the ethanol concentration of the fuel in the fuel main tank.


      W105083E01

  2. Electronic Spark Advance (ESA)

    1. Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.

    2. Ignition timing correction is performed depending on the ethanol concentration of the fuel in the fuel main tank.



  3. VVT-i System



    1. The VVT-i system is designed to control the intake camshaft within a range of 45° (of crankshaft angle) to provide valve timing that is optimally suited to the engine condition. This improves torque in all the speed ranges as well as increasing fuel economy and reducing exhaust emissions.


      W103638E01


      Text in Illustration 
      *1
      Camshaft Position Sensor
      *2
      Camshaft Timing Oil Control Valve Assembly
      *3
      Engine Coolant Temperature Sensor
      *4
      Crankshaft Position Sensor
      *5
      ECM
      *6
      Intake Mass Air Flow Meter Sub-assembly
      *7
      Throttle Position Sensor
      -
      -

      W103630E01

    2. The VVT-i system delivers excellent benefits in the different operating conditions as shown in the table below:

      Operation State
      Objective
      Effect
      During Idling
      W102411E01
      Eliminating overlap reduces blow back to the intake side.
      1. Stabilized idling speed
      2. Better fuel economy
      At Light Load
      W102412E01
      Decreasing overlap to reduce blow back to the intake side.
      Ensured engine stability
      At Medium Load
      W102413E01
      Increasing overlap to increase internal EGR to reduce pumping loss.
      1. Better fuel economy
      2. Improved emission control
      In Low to Medium Speed Range with Heavy Load
      W102414E01
      Advancing the intake valve close timing for volumetric efficiency improvement.
      Improved torque in low to medium speed range
      In High Speed Range with Heavy Load
      W102415E01
      Retarding the intake valve close timing for volumetric efficiency improvement.
      Improved output
      At Low Temperatures
      W102411E01
      Decreasing overlap to reduce blow back to the intake side leads to the lean burning condition, and stabilizes the idling speed at fast idle.
      1. Stabilized fast idle speed
      2. Better fuel economy
      1. Starting Engine
      2. Stopping Engine
      W102411E01
      Decreasing overlap to reduce blow back to the intake side.
      Improved startability



  4. Electronic Throttle Control System-intelligent (ETCS-i)

    1. The ETCS-i is used, providing excellent throttle control in all the operating ranges. The accelerator cable has been discontinued, and an accelerator pedal position sensor has been provided on the accelerator pedal.

    2. In the conventional throttle body, the throttle valve opening is determined by the amount of the accelerator pedal effort. In contrast, the ETCS-i uses the ECM to calculate the optimal throttle valve opening that is appropriate for the respective driving condition and uses a throttle control motor to control the opening.

    3. The ETCS-i controls the Idle Speed Control (ISC) system.



    4. In case of an abnormal condition, this system switches to the limp mode.


      W103632E01

  5. Sub-fuel System Control

    1. When the engine is cold and ethanol concentration in fuel in the fuel main tank is high, the evaporation of fuel becomes difficult. As a result, the engine may not start or be difficult to start only with fuel injection by the fuel injectors. Therefore, the sub-fuel system control operates to inject fuel (E22) in the fuel sub-tank depending on ethanol concentration in fuel in the fuel main tank during cold engine starting, thus assisting engine starting and ensuring drivability immediately after the engine starts.

    2. This system consists of the ECM, FFV relay, fuel sub-tank, sub-tank fuel pump, No. 1 solenoid valve, No. 2 solenoid valve, air fuel ratio sensor, and engine coolant temperature sensor.

  6. Fuel Pump Control

    1. The fuel pump is controlled by the ECM, using the circuit opening relay.

    2. The fuel pump control has a fuel cut control. The fuel cut control stops the fuel pump when any of the Supplemental Restraint System (SRS) airbags have deployed.


CONSTRUCTION


  1. Air Fuel Ratio Sensor and Oxygen Sensor

    1. A planar type air fuel ratio sensor and a cup type oxygen sensor are used. The basic construction of the oxygen sensor and the air fuel ratio sensor is the same. However, they are divided into the cup type and the planar type, in accordance with the different types of heater construction used.

    2. The planar type air fuel ratio sensor uses alumina, which excels in heat conductivity and electrical insulation, to integrate the sensor element with a heater, thus improving the warmup performance of the sensor.



    3. The cup type oxygen sensor contains a sensor element that surrounds the heater.


      W102801E01


      Text in Illustration 
      *A
      Planar Type Air Fuel Ratio Sensor
      *B
      Cup Type Oxygen Sensor
      *1
      Diffusion Resistance Layer
      *2
      Alumina
      *3
      Atmosphere
      *4
      Heater
      *5
      Platinum Electrode
      *6
      Sensor Element (Zirconia)



    4. As illustrated below, the conventional oxygen sensor is characterized by a sudden change in its output voltage at the threshold of the stoichiometric air fuel ratio. In contrast, the air fuel ratio sensor data is approximately proportionate to the existing air fuel ratio. The air fuel ratio sensor converts the oxygen density to current and sends it to the ECM. As a result, the detection precision of the air fuel ratio has been improved. In addition, the ECM uses this output voltage to estimate ethanol concentration in fuel in the fuel main tank. The air fuel ratio sensor data can be viewed using an intelligent tester II.


      W100042E25



  2. Intake Mass Air Flow Meter Sub-assembly

    1. This engine uses the hot-wire type air flow meter designed for direct electrical measurement of the intake air mass flow.



    2. This intake mass air flow meter sub-assembly has a built-in intake air temperature sensor.


      W102872E01


      Text in Illustration 
      *1
      Intake Mass Air Flow Meter Sub-assembly
      *2
      Temperature Sensing Element
      *3
      Platinum Hot-wire Element
      *4
      Intake Air Temperature Sensor
      V100136
      Air Flow
      -
      -



  3. Crankshaft and Camshaft Position Sensors

    1. The timing rotor of the crankshaft consists of 36 teeth, with 2 teeth missing. The crankshaft position sensor outputs the crankshaft rotation signals every 10°, and the missing teeth are used to determine the top dead center.



    2. To detect the camshaft position, a timing rotor on the intake camshaft is used to generate 3 pulses for every 2 revolutions of the crankshaft.


      W102903E01


      Text in Illustration 
      *1
      Crankshaft Position Sensor
      *2
      Timing Rotor
      *3
      Camshaft Position Sensor
      -
      -

      W102904E02



  4. Knock Control Sensor (Flat Type)

    1. In a conventional type knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking* frequency of the engine block. This sensor can only detect vibration in this frequency band.

      1. *: The term "knock" or "knocking" is used in this case to describe either preignition or detonation of the air fuel mixture in the combustion chamber. This preignition or detonation refers to the air fuel mixture being ignited earlier than is advantageous. This use of "knock" or "knocking" is not primarily used to refer to a loud mechanical noise that may be produced by an engine.

    2. A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from approximately 6 kHz to 15 kHz). It has the following features:


      1. The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability has been increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.


        W100047E09

    3. A flat type knock control sensor is installed in an engine by placing it over the stud bolt installed on the cylinder block. For this reason, a hole for the stud bolt exists in the center of the sensor.

    4. In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and the piezoelectric element.



    5. An open/short circuit detection resistor is integrated in the sensor. When the ignition switch is ON, the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect the open/short circuit and store a Diagnostic Trouble Code (DTC).


      W100048E18



    6. Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.


      W102908E01


      Text in Illustration 
      *1
      Steel Weight
      *2
      Piezoelectric Element
      V100135
      Inertia
      -
      -



    7. This sensor is mounted in the specific directions and angles illustrated. To prevent water accumulation in the connector, make sure to install the flat type knock control sensor in the position shown in the following illustration:


      W102301E01


      Text in Illustration 
      *1
      Knock Control Sensor
      -
      -



  5. Throttle Position Sensor

    1. A non-contact type throttle position sensor is used. This sensor uses a Hall IC, which is mounted on the throttle body.

    2. The Hall IC is surrounded by a magnetic yoke. The Hall IC converts the changes that occur in the magnetic flux into electrical signals and outputs them as throttle valve effort to the ECM.



    3. The Hall IC contains circuits for the main and sub signals. It converts the throttle valve opening angles into electric signals with two differing characteristics and outputs them to the ECM.


      W102418E01



  6. Accelerator Pedal Position Sensor

    1. This non-contact type accelerator pedal position sensor uses a Hall IC, which is mounted on the accelerator pedal arm.

    2. A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.



    3. This accelerator pedal position sensor includes 2 Hall ICs and circuits for the main and sub signals. It converts the accelerator pedal depressed angles into electric signals with two differing characteristics and outputs them to the ECM.


      W100142E04



  7. Camshaft Timing Oil Control Valve Assembly



    1. This camshaft timing oil control valve assembly controls the spool valve using duty cycle control from the ECM. This allows hydraulic pressure to be applied to the VVT-i controller advanced or retarded side. When the engine is stopped, the camshaft timing oil control valve assembly is in the most retarded position.


      W102913E01


      Text in Illustration 
      *1
      Spool Valve
      *2
      Sleeve
      *3
      Spring
      *4
      Plunger
      *5
      Coil
      -
      -
      *a
      To VVT-i Controller (Advance Side)
      *b
      To VVT-i Controller (Retard Side)
      *c
      Drain
      *d
      Oil Pressure



  8. Throttle Control Motor



    1. A DC motor with excellent response and minimal power consumption is used for the throttle control motor. The ECM performs the duty cycle control of the direction and the amperage of the current that flows to the throttle control motor in order to regulate the opening of the throttle valve.


      W102914E01


      Text in Illustration 
      *1
      Throttle Body
      *2
      Throttle Valve
      *3
      Throttle Control Motor
      -
      -



  9. Ignition Coil Assembly



    1. The Direct Ignition System (DIS) provides 4 ignition coil assemblies, one for each cylinder. The spark plug caps, which provide contact to spark plugs, are integrated with the ignition coil. Also, an igniter is enclosed to simplify the system.


      W102322E01


      Text in Illustration 
      *1
      Igniter
      *2
      Iron Core
      *3
      Plug Cap
      *4
      Secondary Coil
      *5
      Primary Coil
      -
      -
      *a
      Ignition Coil Cross Section
      -
      -



  10. Spark Plug



    1. Long-reach type spark plugs are used. This type of spark plug allows the area of the cylinder head that receives the spark plugs to be made thick. Thus, the water jacket can be extended near the combustion chamber, which contributes to cooling performance.


      W104441E01


      Text in Illustration 
      *1
      Long-reach Type Spark Plug
      *2
      Conventional Type Spark Plug

    2. To be compatible with alcohol fuel, a double needle type spark plug with superior corrosion resistance is used.



    3. By using an iridium center electrode, ignition performance superior to that of platinum-tipped spark plugs has been achieved and durability has been increased.


      W105084E01


      Text in Illustration 
      *1
      Iridium Tip
      *2
      Platinum Tip


OPERATION


  1. Sequential Multiport Fuel Injection (SFI)



    1. Injection Volume Correction Depending on Ethanol Concentration in Fuel

      1. When ethanol concentration in fuel changes, the stoichiometric air fuel ratio also changes. Therefore, injection volume correction is performed depending on the ethanol concentration of the fuel to ensure starting performance and driveability at various ethanol concentrations.
      2. The stoichiometric air fuel ratio for the gasoline engine vehicle is basically constant. On the other hand, the stoichiometric air fuel ratio for the Flexible Fuel Vehicle (FFV) changes depending on the ethanol concentration of the fuel.
      3. The stoichiometric air fuel ratio for the FFV increases when the ethanol concentration of the fuel is low, and decreases when ethanol concentration of the fuel is high.
      4. The ECM calculates the stoichiometric air fuel ratio of the fuel in the fuel main tank based on the intake air mass, the signal from the air fuel ratio sensor, and the feedback value of the injection volume. Then, the ECM compares the calculated stoichiometric air fuel ratio of the fuel in the fuel main tank with that of gasoline, and estimates ethanol concentration of the fuel in the fuel main tank.
      5. The estimated value of ethanol concentration is updated as necessary.
      6. The ECM performs injection volume correction depending on the estimated ethanol concentration.

      W105085E01


      W105086E01



  2. Electronic Spark Advance (ESA)



    1. Ignition Timing Correction Depending on Ethanol Concentration in Fuel

      1. The ECM performs the correction to make optimum ignition timing based on the estimated ethanol concentration of the fuel in the fuel main tank. As a result, starting performance and driveability at various ethanol concentrations of the fuel in the fuel main tank are ensured.

      W105087E01


      Text in Illustration 
      *1
      ECM
      *2
      Intake Mass Air Flow Meter Sub-assembly
      *3
      Fuel Injector Assembly
      *4
      Ignition Coil Assembly
      *5
      Air Fuel Ratio Sensor
      -
      -



  3. VVT-i System



    1. Using the engine speed, intake air mass, throttle position and engine coolant temperature, the ECM can calculate optimal valve timing for each driving condition and controls the camshaft timing oil control valve assembly. In addition, the ECM uses signals from the camshaft position sensor and the crankshaft position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.


      W104268E01



    2. When the camshaft timing oil control valve assembly is positioned as illustrated below by the advance signals from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction:


      W102423E02


      Text in Illustration (Advance Side Operation) 
      *1
      Vane
      *2
      ECM
      *a
      Rotation Direction
      *b
      In (Oil Pressure)
      *c
      Drain (Oil Pressure)
      -
      -



    3. When the camshaft timing oil control valve assembly is positioned as illustrated below by the retard signals from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction:


      W102965E02


      Text in Illustration (Retard Side Operation) 
      *1
      Vane
      *2
      ECM
      *a
      Rotation Direction
      *b
      Drain (Oil Pressure)
      *c
      In (Oil Pressure)
      -
      -

    4. After reaching the target timing, the valve timing is held by keeping the camshaft timing oil control valve assembly in the neutral position unless the traveling state changes. This adjusts the valve timing at the desired target position and prevents the engine oil from running out when it is unnecessary.



  4. Sub-fuel System Control

    1. ECM estimates the ethanol concentration of the fuel in the fuel main tank based on signals from the air fuel ratio sensor. When the engine is stopped, the ECM stores the ethanol concentration in the memory. When the engine is started, the ECM actuates the sub-tank fuel pump and solenoid valves depending on the water temperature and ethanol concentration in the memory to inject the fuel which is in the fuel sub-tank to the intake ports.

    2. Injection volume is determined based on engine coolant temperature and ethanol concentration of the fuel in the fuel main tank.



    3. Two solenoid valves are used for safety: the No. 1 solenoid valve is used for fuel cut-off for the fuel sub-tank; the No. 2 solenoid valve is used for fuel cut-off and injection volume control for the fuel sub-tank. The No. 1 solenoid valve is operated by ON/OFF control, and the No. 2 solenoid valve is operated by duty cycle control.


      W105088E01


      Text in Illustration 
      *1
      ECM
      *2
      FFV Relay
      *3
      Fuel Sub-tank
      *4
      Sub-tank Fuel Pump
      *5
      Intake Mass Air Flow Meter Sub-assembly
      *6
      No. 1 Solenoid Valve (ON/OFF Control)
      *7
      No. 2 Solenoid Valve (Duty Cycle Control)
      *8
      Fuel Jet
      *9
      Fuel Injector Assembly
      *10
      Engine Coolant Temperature Sensor
      *11
      Air Fuel Ratio Sensor
      -
      -

      W105089E01



  5. Fuel Pump Control



    1. When the ECM detects the airbag deployment signal from the center airbag sensor assembly, it will turn the circuit opening relay off. After the fuel cut control has been activated, turning the ignition switch from off to ON cancels the fuel cut control, and the engine can be restarted.


      W105104E01



  6. ETCS-i

    1. The ECM drives the throttle control motor by determining the target throttle valve opening in accordance with the respective operating condition.



    2. The ECM controls the throttle to an optimal throttle valve opening that is appropriate for the driving conditions such as the amount of accelerator pedal effort and the engine speed in order to achieve excellent throttle control and comfort in all operating ranges.


      W102921E02

    3. The ECM controls the throttle valve in order to constantly maintain an ideal idle speed.