EMISSION CONTROL SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components of the emission control system are as follows:

    Component
    Quantity
    Function
    Oxidation Catalyst*1
    1
    Cleans the exhaust gas particulates, HC and CO.
    ECM
    1
    Controls the emission control system based on signals from each sensor.
    Electric EGR Control Valve Assembly
    1
    Actuated by the ECM, this valve controls the flow rate of EGR gas.*2
    Actuated by the ECM via the E-VRV, this valve controls the flow rate of EGR gas.*3
    EGR Valve Position Sensor (Built into Electric EGR Control Valve Assembly)*4
    1
    Detects the EGR valve position.
    Diesel Throttle Valve
    1
    Actuated by the ECM, this valve controls the flow rate of EGR gas.
    EGR Cooler*4
    1
    Cools EGR gas.
    No. 2 EGR Valve Assembly (EGR Cooler Bypass Switching Valve)*4
    1
    Switches the flow passage of EGR gas in 2 stages.

    1. *1: Models compliant with EURO 4, EURO 3 and Tier 1.5 emission regulations and high altitude countries
    2. *2: Models compliant with Tier 1.5 emission regulations
    3. *3: Except models compliant with Tier 1.5 emission regulations
    4. *4: Models compliant with EURO 4 emission regulations


SYSTEM CONTROL
  1. EGR System

    1. Based on the signals received from the sensors, the ECM determines the EGR volume via the electric EGR control valve assembly and No. 2 EGR valve assembly (EGR cooler bypass switching valve)* in accordance with the engine condition.

      1. *: Models compliant with EURO 4 and Tier 1.5 emission regulations


FUNCTION
  1. EGR System

    1. This system is designed to help reduce and control NOx formation due to a reduction of peak temperature in the engine combustion chamber, which is accomplished by the introduction of an amount of inert gas into the intake manifold.


CONSTRUCTION


  1. Oxidation Catalyst (Models Compliant with EURO 4, EURO 3 and Tier 1.5 Emission Regulations and Models for High Altitude Countries)



    1. An oxidation catalyst is used to clean the exhaust gas particulates, HC, and CO.


      W104904E01


      Text in Illustration 
      *A
      Models Compliant with EURO 4 and Tier 1.5 Emission Regulations
      *B
      Models Compliant with EURO 3 Emission Regulations and Models for High Altitude Countries
      *1
      Front Exhaust Pipe Assembly
      *2
      Oxidation Catalyst



  2. Electric EGR Control Valve Assembly (Models Compliant with Tier 1.5 Emission Regulations)

    1. A DC motor type electric EGR control valve assembly is used. The placement of the electric EGR control valve assembly at the intersection between the intake passage and EGR bypass facilitates the uniform distribution of EGR gas and intake air.



    2. An EGR valve position sensor is provided in the electric EGR control valve assembly. This sensor enables EGR valve control at a higher level of precision by detecting the opening angle of the EGR valve.


      W104547E01


      Text in Illustration 
      *1
      Electric EGR Control Valve Assembly
      *2
      EGR Valve Position Sensor
      *3
      DC Motor Portion
      *4
      EGR Valve
      *5
      Diesel Throttle Body Assembly
      -
      -
      *a
      View from Back Side
      -
      -
      V100136
      Intake Air
      V100135
      EGR Gas
      V100137
      Front
      -
      -



  3. Electric EGR Control Valve Assembly (Models Compliant with EURO 4, EURO 3 and EURO 1 Emission Regulations)

    1. A vacuum actuated type electric EGR control valve assembly is used.

    2. The electric EGR control valve assembly is provided midstream in the intake air passage. By cooling the electric EGR control valve assembly in this manner, a greater volume of exhaust gas can be processed.



    3. On the models compliant with EURO 4 emission regulations, an EGR valve position sensor is provided in the electric EGR control valve assembly in order to directly measure the actual amount of the valve opening. This measurement is then input into the ECM in order to improve the precision of EGR control.


      W102877E01


      Text in Illustration (Models Compliant with EURO 4 Emission Regulations:) 
      *1
      Electric EGR Control Valve Assembly
      *2
      Vacuum Port
      *3
      EGR Valve
      *4
      Air Port
      *5
      EGR Valve Position Sensor
      -
      -
      *a
      From Diesel Throttle Body
      *b
      To Intake Manifold
      *c
      From EGR Pipe Sub-assembly
      -
      -
      V100136
      Intake Air
      V100135
      EGR Gas

      W102876E01


      Text in Illustration (Models Compliant with EURO 3 and EURO 1 Emission Regulations:) 
      *1
      Electric EGR Control Valve Assembly
      *2
      Vacuum Port
      *3
      EGR Valve
      *4
      Air Port
      *a
      From Diesel Throttle Body
      *b
      To Intake Manifold
      *c
      From EGR Pipe Sub-assembly
      -
      -
      V100136
      Intake Air
      V100135
      EGR Gas



  4. EGR Pipe Sub-assembly and No. 2 EGR Valve Assembly (Models Compliant with EURO 4 and Tier 1.5 Emission Regulations)

    1. A water-cooled type EGR cooler is used in the EGR pipe sub-assembly between the cylinder head and EGR valve. In the water-cooled type EGR cooler, engine coolant flows through the eight-layered*1 or six-layered*2 gas passage to cool down the EGR gas.

      1. *1: Models compliant with Tier 1.5 emission regulations
      2. *2: Models compliant with EURO 4 emission regulations



    2. A No. 2 EGR valve assembly (EGR cooler bypass switching valve) is used. If EGR gas is cooled down in the EGR cooler with light engine load and low engine coolant temperature, compression air temperature decreases. To prevent this, the EGR gas passage is switched by the EGR cooler bypass switching valve. The EGR passage is switched in 2 stages.


      W104548E01


      Text in Illustration (Models Compliant with Tier 1.5 Emission Regulations:) 
      *1
      EGR Pipe Sub-assembly
      *2
      Engine Coolant Inlet
      *3
      Actuator for EGR Cooler Bypass Switching Valve
      *4
      No. 2 EGR Valve Assembly
      *5
      EGR Cooler Bypass Switching Valve
      *6
      Engine Coolant Outlet
      *7
      Bypass Passage
      *8
      EGR Cooler
      *9
      EGR Gas Passage
      *10
      Engine Coolant Passage
      *a
      View from Upper Side
      *b
      EGR Cooler Cross Section
      V100135
      EGR Gas
      V100136
      EGR Gas (through EGR Cooler)
      V100137
      EGR Gas (through Bypass Passage)
      -
      -

      W102355E03


      Text in Illustration (Models Compliant with EURO 4 Emission Regulations:) 
      *1
      EGR Pipe Sub-assembly
      *2
      Engine Coolant Inlet
      *3
      Actuator for EGR Cooler Bypass Switching Valve
      *4
      No. 2 EGR Valve Assembly
      *5
      EGR Cooler Bypass Switching Valve
      *6
      Engine Coolant Outlet
      *7
      Bypass Passage
      *8
      EGR Cooler
      *9
      EGR Gas Passage
      *10
      Engine Coolant Passage
      *a
      View from Upper Side
      *b
      Cross Section
      V100135
      EGR Gas
      V100136
      EGR Gas (through EGR Cooler)
      V100137
      EGR Gas (through Bypass Passage)
      -
      -


OPERATION
  1. EGR System

    1. On the models compliant with Tier 1.5 emission regulations, EGR system carries out the following controls:

      1. The ECM actuates the electric EGR control valve assembly, which regulates volume of EGR gas recirculation, in accordance with the engine conditions.

      2. The ECM switches the bypass passage of the EGR pipe sub-assembly via the VSV (for EGR cooler bypass switching valve) in 2 stages in order to optimize the temperature of the EGR gas and clean exhaust gases.


        W109665E01


        Text in Illustration 
        *1
        Engine
        *2
        EGR Passage in Cylinder Head
        *3
        Exhaust Manifold
        *4
        Oxidation Catalyst
        *5
        EGR Pipe Sub-assembly
        *6
        Bypass Passage
        *7
        EGR Cooler
        *8
        No. 2 EGR Valve Assembly
        *9
        EGR Cooler Bypass Switching Valve
        *10
        Actuator for EGR Cooler Bypass Switching Valve
        *11
        VSV (for EGR Cooler Bypass Switching Valve)
        *12
        Vacuum Pump
        *13
        EGR Valve
        *14
        EGR Valve Position Sensor
        *15
        DC Motor for EGR Valve Control
        *16
        Throttle Position Sensor
        *17
        Diesel Throttle Valve
        *18
        Throttle Control Motor
        *19
        ECM
        *20
        Atmospheric Pressure Sensor
        *21
        Crank Position Sensor
        *22
        Accelerator Pedal Position Sensor
        *23
        Engine Coolant Temperature Sensor
        *24
        Turbo Pressure Sensor
        *25
        Intake Air Temperature Sensor
        *26
        Intake Mass Air Flow Meter Sub-assembly
        V100135
        Exhaust Gas
        V100136
        Intake Air

    2. On the models compliant with EURO 4, EURO3 and EURO 1 emission regulations, EGR system carries out the following controls:

      1. By sensing the engine driving conditions and actual amount of EGR valve opening*, the ECM electrically operates the E-VRV (for EGR valve control) and VSV (for EGR valve close), which control the magnitude of vacuum introduced into the diaphragm of the electric EGR control valve assembly. In addition, the ECM controls the diesel throttle valve opening position using the throttle control motor. As a result, the amount of recirculating exhaust gas is regulated. EGR valve opening lift is controlled by modulated negative pressure.
        1. *: Models compliant with EURO 4 emission regulations
      2. The VSV (for EGR valve close) is activated when the EGR control is stopped, in order to introduce the atmospheric pressure to the diaphragm of electric EGR control valve assembly and improve EGR valve closure response to maintain driveability.

      3. On the models compliant with EURO 4 emission regulations, the ECM switches the bypass passage of the EGR pipe sub-assembly via the VSV (for EGR cooler bypass switching valve) in 2 stages in order to optimize the temperature of the EGR gas and clean exhaust gases.


        W109663E01


        Text in Illustration (Models Compliant with EURO 4 Emission Regulations:) 
        *1
        Engine
        *2
        EGR Passage in Cylinder Head
        *3
        Exhaust Manifold
        *4
        Oxidation Catalyst
        *5
        Electric EGR Control Valve Assembly
        *6
        EGR Valve Position Sensor
        *7
        EGR Valve
        *8
        No. 2 EGR Valve Assembly
        *9
        EGR Cooler Bypass Switching Valve
        *10
        Actuator for EGR Cooler Bypass Switching Valve
        *11
        EGR Pipe Sub-assembly
        *12
        Bypass Passage
        *13
        EGR Cooler
        *14
        VSV (for EGR Cooler Bypass Switching Valve)
        *15
        Vacuum Damper
        *16
        VSV (for EGR Valve Close)
        *17
        Throttle Position Sensor
        *18
        Diesel Throttle Valve
        *19
        Throttle Control Motor
        *20
        Vacuum Pump
        *21
        E-VRV (for EGR Valve Control)
        *22
        ECM
        *23
        Atmospheric Pressure Sensor
        *24
        Crank Position Sensor
        *25
        Accelerator Pedal Position Sensor
        *26
        Engine Coolant Temperature Sensor
        *27
        Turbo Pressure Sensor
        *28
        Intake Air Temperature Sensor
        *29
        Intake Mass Air Flow Meter Sub-assembly
        -
        -
        V100135
        Exhaust Gas
        V100136
        Intake Air


        W109658E02


        Text in Illustration (Models Compliant with EURO 3 and EURO 1 Emission Regulations:) 
        *A
        Models Compliant with EURO 3 Emission Regulations and Models for High Altitude Countries
        -
        -
        *1
        Engine
        *2
        EGR Passage in Cylinder Head
        *3
        Exhaust Manifold
        *4
        Oxidation Catalyst
        *5
        Electric EGR Control Valve Assembly
        *6
        EGR Valve
        *7
        EGR Pipe Sub-assembly
        *8
        Vacuum Damper
        *9
        VSV (for EGR Valve Close)
        *10
        Throttle Position Sensor
        *11
        Diesel Throttle Valve
        *12
        Throttle Control Motor
        *13
        Vacuum Pump
        *14
        E-VRV (for EGR Valve Control)
        *15
        ECM
        *16
        Atmospheric Pressure Sensor
        *17
        Crank Position Sensor
        *18
        Accelerator Pedal Position Sensor
        *19
        Engine Coolant Temperature Sensor
        *20
        Turbo Pressure Sensor
        *21
        Intake Air Temperature Sensor
        *22
        Intake Mass Air Flow Meter Sub-assembly
        V100135
        Exhaust Gas
        V100136
        Intake Air