AUTOMATIC TRANSMISSION SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS

Component
Function
Torque Converter Assembly
  1. Transmits the engine power to the transmission.
  2. Increases engine torque.
Oil Pump
Provides oil pressure necessary for the transmission operation.
Overdrive Direct Clutch (C0)
Connects the overdrive planetary sun gear and the overdrive planetary carrier.
Forward Clutch (C1)
Connects the input shaft and the front planetary ring gear.
Direct Clutch (C2)
Connects the input shaft and the front and rear planetary sun gear.
Overdrive Brake (B0)
Prevents the overdrive planetary sun gear from turning either clockwise or counterclockwise.
2nd Coast Brake (B1)
Prevents the front and rear sun gear from turning either clockwise or counterclockwise.
2nd Brake (B2)
Prevents the outer race of F1 from turning either clockwise or counterclockwise, thus preventing the front and rear sun gear from turning counterclockwise.
1st and Reverse Brake (B3)
Prevents the rear planetary carrier from turning either clockwise or counterclockwise.
Overdrive 1-way Clutch (F0)
Connects the overdrive planetary sun gear and the planetary carrier when engine power is transmitted to the overdrive input shaft.
1-way Clutch Assembly (F1)
Prevents the front and rear planetary sun gear from turning counterclockwise when B2 is operating.
No. 2 1-way Clutch (F2)
Prevents the rear planetary carrier from turning counterclockwise.
Planetary Gears
Change power transmission route in accordance with clutch and brake operation, and increase or decrease output shaft revolutions accordingly.
Shift Solenoid Valve S1 and S2
Switch the shift valves.
Shift Solenoid Valve SLT
Controls line pressure.
Shift Solenoid Valve SL
Controls the lock-up clutch.
ATF Temperature Sensor
Detects the ATF temperature.
Input Speed Sensor (NCO)
Detects the input speed of the transmission.
Output Speed Sensor (SP2)
Detects the output speed of the transmission.
Park/Neutral Position Switch Assembly
Detects the shift lever position (P, R, N, D, 2, L).
Shift Lock Control ECU Sub-assembly
Transmission Control Switch
Detects that the shift lever is in 3.
ECM
  1. Controls each shift solenoid valve and engine output in response to a signal from each sensor and switch.
  2. Makes a diagnosis and memorizes the failed section when the ECM detects a malfunction.
Combination Meter Assembly
Shift Position Indicator Light
Indicates the shift lever position.
MIL
Illuminates or blinks to inform the driver when the ECM detects a malfunction.
DLC3
The Diagnostic Trouble Codes (DTCs) can be read by connecting an intelligent tester II.

SYSTEM CONTROL

Electronic Control of Automatic Transmission 
Control
Function
Shift Timing Control
The ECM sends current to the shift solenoid valves S1 and/or S2 based on signals from various sensors in order to shift the gears.
Line Pressure Control
Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transmission.
Engine Torque Control
Retards the ignition timing temporarily to improve shift feeling during upshifting or downshifting.
N to D Squat Control
When the shift lever is moved from N to D, the gear is temporarily engaged to the 4th and then to the 1st to reduce vehicle squat.
Lock-up Timing Control
The ECM sends current to the shift solenoid valve SL based on signals from various sensors and engages or disengages the lock-up clutch.


  1. Line Pressure Control

    1. In order to obtain a predetermined line pressure characteristic in accordance with each sensor signal, the ECM activates the shift solenoid valve SLT to regulate the throttle pressure.



    2. This makes it possible for the primary regulator valve to precisely and minutely control the line pressure in accordance with the engine output, thus providing smoother shift characteristics.


      X105538E01



  2. Engine Torque Control



    1. Engagement of the clutches and brakes of the planetary gear unit in the transmission is controlled smoothly by momentarily retarding the engine ignition timing when gears are shifted up or down in the transmission. When the ECM judges a gear shift timing in accordance with signals, it activates the shift solenoid valves to perform gear shifting. When the gear shifting starts, the ECM retards the engine ignition timing to reduce the engine torque. As a result, engagement force of the clutches and brakes of the planetary gear units is weakened and the gear change is performed smoothly.


      X105542E01

  3. Lock-up Timing Control

    1. The ECM operates the lock-up timing control in order to improve the fuel consumption performance in the top gear when the shift lever is in D or 3.

      Lock-up Timing Control Operation 
      Gear
      Shift Lever Position
      D
      3
      1st
      X
      X
      2nd
      X
      X
      3rd
      X
      ○
      4th
      ○
      -

      HINT:
      ○: Operates
      X: Does not operate


FUNCTION


  1. Shift Lock System

    1. The shift lock system prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON and the brake pedal is depressed. This prevents the vehicle from starting off suddenly.

    2. The shift lock system is controlled by the shift lock control ECU sub-assembly and it has a shift lock function and key interlock function.

    3. The shift lock control ECU sub-assembly has a built-in P detection switch to detect the shift lever position, and receives input signals from the stop light switch assembly and ignition switch. Upon receiving these signals, the shift lock control ECU sub-assembly turns on the shift lock solenoid and the key interlock solenoid in order to release the shift lock and key interlock.

    4. The key interlock function prevents the key from being pulled out after the ignition switch has been turned off, unless the shift lever has been moved to P. Thus, the driver is urged to park the vehicle with the shift lever in P.



    5. A shift lock release button, which manually overrides the shift lock mechanism, is used.


      X102150E01


CONSTRUCTION


  1. Torque Converter Assembly



    1. A compact, lightweight and high-capacity torque converter assembly is used. The torque converter supports lock-up clutch control, thus improving fuel economy.


      X105543E01


      Text in Illustration 
      *1
      Lock-up Clutch
      *2
      Turbine Runner
      *3
      1-way Clutch
      *4
      Stator
      *5
      Pump Impeller
      -
      -



  2. Oil Pump Assembly



    1. The oil pump is operated by the torque converter assembly. It lubricates the planetary gear units and supplies operating fluid pressure for hydraulic control. The front oil pump drive gear is continually driven by the engine via the pump impeller. The pump has sufficient capacity to supply the necessary fluid pressure throughout all speed ranges, as well as in reverse.


      X105545E01


      Text in Illustration 
      *1
      Oil Seal
      *2
      Front Oil Pump Body Sub-assembly
      *3
      Front Oil Pump Drive Gear
      *4
      Oil Pump Cover
      *5
      Stator Shaft Assembly
      *6
      Front Oil Pump Driven Gear



  3. Planetary Gear Unit



    1. The gear train consists of three multi-plate clutches, three multi-plate brakes, a single band type brake, three 1-way clutches, and three sets of planetary gears each consisting of a sun gear, a pinion gear and a ring gear.


      X105549E01


      Text in Illustration (Models with 2TR-FE Engine:) 
      *1
      Overdrive Input Shaft
      *2
      Overdrive Planetary Gear Assembly
      *3
      Input Shaft
      *4
      Front Planetary Gear Assembly
      *5
      Output Shaft
      *6
      Rear Planetary Gear Assembly
      *7
      No. 2 1-way Clutch (F2)
      *8
      1st and Reverse Brake (B3)
      *9
      1-way Clutch Assembly (F1)
      *10
      2nd Brake (B2)
      *11
      Forward Clutch (C1)
      *12
      Direct Clutch (C2)
      *13
      2nd Coast Brake (B1)
      *14
      Overdrive 1-way Clutch (F0)
      *15
      Overdrive Direct Clutch (C0)
      *16
      Overdrive Brake (B0)

      X102154E01


      Text in Illustration 
      *1
      Overdrive Input Shaft
      *2
      Overdrive Planetary Gear Assembly
      *3
      Input Shaft
      *4
      Front Planetary Gear Assembly
      *5
      Rear Planetary Gear Assembly
      *6
      Output Shaft



  4. Transmission Valve Body Assembly



    1. The transmission valve body assembly consists of upper and lower valve bodies and 4 shift solenoid valves.


      X105552E01


      Text in Illustration 
      *1
      Upper Valve Body
      *2
      Lower Valve Body
      *3
      Shift Solenoid Valve SL
      *4
      Shift Solenoid Valve SLT
      *5
      Shift Solenoid Valve S2
      *6
      Shift Solenoid Valve S1
      *7
      Plate
      -
      -

      X102156E04


      Text in Illustration (Upper Valve Body) 
      *1
      Lock-up Relay Valve
      *2
      3-4 Shift Valve
      *3
      2nd Coast Modulator Valve
      *4
      B3 Check Valve
      *5
      C2 Check Valve
      *6
      Reverse Control Valve
      *7
      2-3 Shift Valve
      *8
      Secondary Regulator Valve

      X102157E03


      Text in Illustration (Lower Valve Body) 
      *1
      Primary Regulator Valve
      *2
      1-2 Shift Valve
      *3
      Low Coast Modulator Valve
      *4
      Accumulator Control Valve
      *5
      Solenoid Modulator Valve
      *6
      Cut Back Valve
      *7
      Lock-up Control Valve
      -
      -



  5. Shift Solenoid Valves S1 and S2

    1. The shift solenoid valves S1 and S2 are 2-way solenoid valves.



    2. A filter is provided at the tip of each solenoid valve to further improve operational reliability.


      X104738E01


      Text in Illustration (Shift Solenoid Valves S1 and S2) 
      *1
      Filter
      -
      -
      V100135
      Line Pressure
      V100136
      Control Pressure

      Function of Shift Solenoid Valves S1 and S2 
      Shift Solenoid Valve
      Function
      S1
      Switches the 2-3 shift valve.
      S2
      Switches the 1-2 shift valve and the 3-4 shift valve.



  6. Shift Solenoid Valves SLT and SL



    1. In order to provide a hydraulic pressure that is proportional to the current that flows to the solenoid coil, the shift solenoid valve SLT linearly controls the line pressure based on the signals it receives from the ECM.


      X102159E02

    2. The shift solenoid valve SL is a 2-way solenoid valve.



    3. A filter is provided at the tip of the solenoid valve to further improve operational reliability.


      X104738E01


      Text in Illustration (Shift Solenoid Valve SL) 
      *1
      Filter
      -
      -
      V100135
      Line Pressure
      V100136
      Control Pressure

      Function of Shift Solenoid Valves SLT and SL 
      Shift Solenoid Valve
      Function
      SLT
      1. Line pressure control
      2. Accumulator back pressure control
      SL
      1. Lock-up clutch pressure control
      2. Accumulator back pressure control



  7. ATF Temperature Sensor



    1. An ATF temperature sensor, which is provided on the oil outlet, detects the ATF oil temperature necessary for shifting and for various controls and sends the information to the ECM.


      X105562E01


      Text in Illustration 
      *1
      ATF Temperature Sensor
      -
      -



  8. Speed Sensors

    1. This automatic transmission uses an input speed sensor (for NCO signal) and an output speed sensor (for SP2 signal). Thus, the ECM can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to various conditions.

    2. These speed sensors are the pick-up coil type.

    3. The input speed sensor detects the input speed of the transmission. The overdrive direct clutch drum is used as the timing rotor for this sensor.



    4. The output speed sensor detects the speed of the output shaft.


      X105567E01


      Text in Illustration 
      *1
      Overdrive Direct Clutch Drum
      *2
      Input Speed Sensor
      *3
      Output Speed Sensor
      *4
      Output Shaft



  9. Park/Neutral Position Switch Assembly and Transmission Control Switch

    1. The ECM uses the park/neutral position switch assembly and the transmission control switch to detect the shift lever position.

    2. The park/neutral position switch assembly sends the R, 2, L and NSW signals to the ECM. It also sends signals for the shift position indicator "P, R, N, 2 and L" in the combination meter assembly.



    3. The transmission control switch is located in the shift lock control ECU sub-assembly. This switch sends the 3 signal to the ECM. It also sends a signal for the shift position indicator "D and 3" in the combination meter assembly.


      X105570E01



  10. Shift Control Mechanism

    1. A gate type shift lever that uses a transmission control cable is used.



    2. The shift control mechanism consists of a transmission floor shift assembly and a transmission control cable assembly.


      X105574E01


      Text in Illustration 
      *1
      Transmission Floor Shift Assembly
      *2
      Transmission Control Cable Assembly
      *3
      Shift Lever Knob
      -
      -
      *a
      Shift Pattern
      -
      -


OPERATION


  1. Transmission Power Flow

    Operating Condition 
    Shift Lever Position and Gear Range
    Gear Position
    Shift Solenoid Valve
    Clutch
    Brake
    1-way Clutch
    S1
    S2
    C0
    C1
    C2
    B0
    B1
    B2
    B3
    F0
    F1
    F2
    P
    Park
    On
    Off
    ○
    -
    -
    -
    -
    -
    -
    -
    -
    -
    R
    Reverse
    On
    Off
    ○
    -
    ○
    -
    -
    -
    ○
    ○
    -
    -
    N
    Neutral
    On
    Off
    ○
    -
    -
    -
    -
    -
    -
    -
    -
    -
    D
    1st
    On
    Off
    ○
    ○
    -
    -
    -
    -
    -
    ○
    -
    ○
    2nd
    On
    On
    ○
    ○
    -
    -
    -
    ○
    -
    ○
    ○
    -
    3rd
    Off
    On
    ○
    ○
    ○
    -
    -
    ○
    -
    ○
    -
    -
    4th
    Off
    Off
    -
    ○
    ○
    ○
    -
    ○
    -
    -
    -
    -
    3
    1st
    On
    Off
    ○
    ○
    -
    -
    -
    -
    -
    ○
    -
    ○
    2nd
    On
    On
    ○
    ○
    -
    -
    -
    ○
    -
    ○
    ○
    -
    3rd
    Off
    On
    ○
    ○
    ○
    -
    -
    ○
    -
    ○
    -
    -
    2
    1st
    On
    Off
    ○
    ○
    -
    -
    -
    -
    -
    ○
    -
    ○
    2nd*
    On
    On
    ○
    ○
    -
    -
    (○)
    ○
    -
    ○
    ○
    -
    L
    1st*
    On
    Off
    ○
    ○
    -
    -
    -
    -
    (○)
    ○
    -
    ○

    HINT:
    ○: Operates
    (○): Operates during engine braking
    -: Does not operate
    *: Engine braking occurs




    1. 1st Gear (Shift Lever in D, 3 or 2)


      X104731


      Text in Illustration 
      V100143
      Operates
      -
      -



    2. 2nd Gear (Shift Lever in D or 3)


      X104732


      Text in Illustration 
      V100143
      Operates
      -
      -



    3. 3rd Gear (Shift Lever in D or 3)


      X104733


      Text in Illustration 
      V100143
      Operates
      -
      -



    4. 4th Gear (Shift Lever in D)


      X104734


      Text in Illustration 
      V100143
      Operates
      -
      -



    5. Engine Braking in 1st Gear (Shift Lever in L)


      X104735


      Text in Illustration 
      V100143
      Operates
      V100145
      Operate during Engine Braking



    6. Engine Braking in 2nd Gear (Shift Lever in 2 or L)


      X104736


      Text in Illustration 
      V100143
      Operates
      V100145
      Operate during Engine Braking



    7. Reverse Gear (Shift Lever in R)


      X104737


      Text in Illustration 
      V100143
      Operates
      -
      -


FAIL-SAFE
  1. The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or a solenoid.

    Fail-safe Control List 
    Malfunction Part
    Function
    Output Speed Sensor (SP2)
    During an output speed sensor malfunction, shift control is effected through the input speed sensor signal (NCO) or engine speed signal (NE).
    ATF Temperature Sensor
    During a malfunction of the ATF temperature sensor, the system effects control by fixing the ATF temperature at 80°C (176°F).
    Shift Solenoid Valve S1/S2
    The current to the failed shift solenoid valve is cut off and control is effected by operating the other solenoid valves with normal operation.
    Shift Solenoid Valve SLT
    During a shift solenoid valve SLT malfunction, the current to the shift solenoid valve is stopped. This stops line pressure control, thus increasing shift shock. However, shifting is effected through normal clutch pressure control.
    Shift Solenoid Valve SL
    During a shift solenoid valve SL malfunction, the current to the shift solenoid valve is stopped. This stops lock-up control, thus decreasing fuel economy.


DIAGNOSIS
  1. When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the ECM illuminates or blinks the MIL in the combination meter assembly to inform the driver.

  2. The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions.

  3. The DTCs can be read by connecting an intelligent tester II to the DLC3.

  4. For details, refer to the corresponding Repair Manual for this model.