Home › ENGINE ยท 2KD-FTV › CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR DRIVE END FRAME BEARING


    A102672E01
  1. Using SST and a press, press in a new bearing.

    SST
    09950-60010   (09951-00520)
    09950-70010   (09951-07100)



    A079311E02
  1. Align the claws of the bearing retainer with the grooves inside the generator drive end frame.
    Text in Illustration 
    *1
    Claw

  1. Install the bearing retainer with the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }



2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the rotor and washer to the drive end frame.



3. INSTALL GENERATOR COIL ASSEMBLY


    A158387E02
  1. Using a 21 mm deep socket wrench and press, slowly press on the generator coil.
    Text in Illustration 
    *1
    21 mm Deep Socket Wrench

  1. Install the generator coil with the 4 through bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }



4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    A113845E06
  1. While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.
    Text in Illustration 
    *1
    Pin



    A079303E03
  1. Install the brush holder with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the brush holder.
    Text in Illustration 
    *1
    Pin



5. INSTALL TERMINAL INSULATOR


6. INSTALL GENERATOR REAR END COVER
  1. Install the generator rear end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }



7. INSTALL GENERATOR WITH CLUTCH PULLEY
  1. Install the pulley by hand.

  1. Mount generator in a vise between aluminum plates.



    A203706E01
  1. Install SST (A) and (B) to the generator with clutch pulley as shown in the illustration.

    SST
    09820-63021  

    NOTICE:
    Securely attach SST to the generator with clutch pulley and generator rotor shaft.



    A203708E05
  1. Use a wrench to hold SST (A) and turn SST (B) clockwise to tighten the generator with clutch pulley.

    Torque:
    without SST:
    111 N*m{ 1127 kgf*cm , 81 ft.*lbf }
    with SST:
    83 N*m{ 844 kgf*cm , 61 ft.*lbf }

    Text in Illustration 
    *1
    Fulcrum Length
    *a
    Hold
    V100135
    Turn

    NOTICE:
    Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.

  1. Remove SST from the generator.

  1. Check that the generator pulley rotates smoothly.

  1. Install a new generator pulley cap.