GTS Display
| Measurement Item
| Diagnostic Note
|
Vehicle Speed
| Vehicle speed
| The speed indicated on the speedometer.
|
Target Idle Engine Speed
| Target idling speed
| -
|
Engine Speed
| Engine speed
| -
|
Calculate Load
| Calculated load
| The load calculated by the ECM.
|
MAF
| Mass air flow volume
| If approximately 0.0 gm/s:
- The mass air flow meter power source circuit is open or shorted.
- The VG circuit is open or shorted.
- The E2G circuit is open.
|
Atmosphere Pressure
| Atmospheric pressure
| -
|
MAP
| Absolute pressure inside intake manifold
| -
|
Coolant Temp
| Engine coolant temperature
| If -40°C (-40°F), the sensor circuit is open. If 140°C (284°F) or higher, the sensor circuit is shorted.
|
Intake Air
| Intake air temperature
| If -40°C (-40°F), the sensor circuit is open. If 140°C (284°F) or higher, the sensor circuit is shorted.
|
Intake Air Temp (Turbo)
| Intake air temperature after intercooler
| If -40°C (-40°F), the sensor circuit is open. If 190°C (374°F) or higher, the sensor circuit is shorted.
|
Engine Run Time
| Accumulated engine running time
| -
|
Initial Engine Coolant Temp
| Engine coolant temperature at engine start
| -
|
Initial Intake Air Temp
| Intake air temperature at engine start
| -
|
Battery Voltage
| Battery voltage
| -
|
Glow Control Unit Duty
| Glow control unit duty
| -
|
Accel Position
| Accelerator pedal position sensor
| -
|
Accel Sens. No.1 Volt %
| Accelerator pedal position No. 1 output voltage
| -
|
Accel Sens. No.2 Volt %
| Accelerator pedal position No. 2 output voltage
| -
|
Target Throttle Position
| Target throttle position
| -
|
Actual Throttle Position
| Actual throttle position
| -
|
Diesel Throttle Learn Status
| Diesel throttle learning status
| -
|
Throttle Sensor Volt %
| Throttle position sensor output voltage
| -
|
Throttle Motor DUTY
| Throttle actuator
| -
|
Injection Volume
| Injection volume
| -
|
Total Injection Volume
| Total injection volume
| -
|
Inj. FB Vol. for Idle
| Injection feedback value for idle speed control
| -
|
Injection Feedback Val #1 to #4
| Injection volume correction for cylinder 1 to 4
| -
|
Injection Volume #1 to #4
| Injection volume for cylinder 1 to 4
| -
|
Pre Injection Period
| Pre injection period
| -
|
Pilot 1 Injection Period
| Pilot 1 injection period
| -
|
Pilot 2 Injection Period
| Pilot 2 injection period
| -
|
Main Injection Period
| Main injection period
| -
|
After Injection Period
| Post injection period
| -
|
Pre Injection Timing
| Pre injection timing
| -
|
Pilot 1 Injection Timing
| Pilot 1 injection timing
| -
|
Pilot 2 Injection Timing
| Pilot 2 injection timing
| -
|
Main Injection Timing
| Main injection timing
| -
|
After Injection Timing
| Post injection timing
| -
|
i-ART Learning Status #1 to #4
| Injector learning status for cylinder 1 to 4
| -
|
i-ART Learning Status History #1 to #4
| Injector learning status history for cylinder 1 to 4
| -
|
Injector Leaking Count #1 to #4
| Injector leaking count for cylinder 1 to 4
| -
|
Target Common Rail Pressure
| Target common rail pressure
| -
|
Fuel Press
| Fuel pressure
| -
|
Fuel Pressure #1 to #4
| Fuel pressure for cylinder 1 to 4
| -
|
Fuel Temperature #1 to #4
| Fuel temperature for cylinder 1 to 4
| -
|
Fuel Return Temp
| Fuel return temperature
| -
|
Target Pump SCV Current
| Final pump current target value
| -
|
Pump SCV Learning Value
| Pump current learned value
| -
|
Pressure Discharge Valve
| Pressure discharge valve operation prohibition
| -
|
Target EGR Position
| Target EGR valve position
| -
|
Actual EGR Valve Pos.
| Actual EGR valve position
| -
|
EGR Motor Duty #1
| EGR motor duty ratio
| -
|
EGR Close Lrn. Val.
| EGR valve fully closed position learned value
| -
|
EGR Close Lrn. Status
| EGR valve fully closed position learning status
| -
|
EGR Operation Prohibit
| EGR operation prohibition
| -
|
EGR Cooler Bypass VSV
| Vacuum switching valve (for EGR bypass valve) status
| -
|
EGR Cooler Bypass Position
| EGR cooler bypass position
| -
|
Target Booster Pressure
| Target booster pressure
| -
|
VN Turbo Command
| VN turbo command
| -
|
Actual VN Position
| Actual VN turbo position
| -
|
VN Position Sensor Out
| VN position sensor output voltage
| -
|
VN Motor Duty
| VN turbo motor duty
| -
|
VN Close Learn Value
| VN turbo fully closed position learned value
| -
|
VN Close Learn Status
| VN turbo fully closed position learning status
| -
|
Starter Signal
| Starter signal
| -
|
Neutral Position SW Signal
| Neutral position switch signal
| -
|
Stop Light Switch
| Stop light switch
| -
|
A/C Signal
| Air conditioning signal
| -
|
Immobiliser Communication
| Immobiliser communication
| -
|
Time after DTC Cleared
| Cumulative time after DTC cleared
| -
|
Distance from DTC Cleared
| Accumulated distance after DTC cleared
| -
|
Warmup Cycle Cleared DTC
| Warmup cycles after DTC cleared
| -
|
TC and TE1
| TC and TE1 terminals of DLC3
| -
|
Engine Start Time
| -
| This item is used for troubleshooting when DTC P1604 is stored.
|
Engine Speed (Starter Off)
| -
| This item is used for troubleshooting when DTC P1604 is stored.
|
Starter Count
| -
| This item is used for troubleshooting when DTC P1604 is stored.
|
Run Dist of Previous Trip
| -
| This item is used for troubleshooting when DTC P1604 is stored.
|
Glow Request Lighting Time
| Glow request lighting time
| This item is used for troubleshooting when DTC P1604 is stored.
|
IG-ON Time
| Ignition switch ON time before engine start
| This item is used for troubleshooting when DTC P1604 is stored.
|
MAF Low
| Mass air flow low
| This item is used for troubleshooting when DTC P1608 is stored.
|
Boost Pressure Low
| Boost pressure low
| This item is used for troubleshooting when DTC P1608 is stored.
|
Common Rail Pressure Low
| Common rail pressure low
| This item is used for troubleshooting when DTC P1608 is stored.
|
Engine Coolant Temp High
| Engine coolant temperature high
| This item is used for troubleshooting when DTC P1608 is stored.
|
MAF/Estimate MAF Ratio
| Indicates the ratio of estimated intake air volume and the actual intake air volume
| This item is used for troubleshooting when DTC P1608 is stored.
|
Rough Idle #1 to #4
| Rough idle status of cylinder 1 to 4
| This item is used for troubleshooting when DTC P1605 is stored.
|
Electric Duty Feedback Value
| -
| -
|
A/C Duty Feedback Value
| -
| -
|
PS Duty Feedback Value
| -
| -
|
Swirl Control Valve VSV
| Vacuum switching valve (for swirl control valve)
| -
|
ACT VSV
| A/C cut status for Active Test
| -
|
Immobiliser Fuel Cut History
| Status of the immobiliser fuel cut history
| -
|
Fuel Remaining Volume
| Fuel remaining volume
| -
|
Received MIL from ECT
| MIL status from ECT
| -
|
Shift Position Sig from ECT
| Shift position from ECT
| -
|
A/T Oil Temp from ECT
| ATF temperature from ECT
| -
|
SPD (NO)
| Output shaft speed
| -
|
ECT Lock Up
| ECT lock-up status
| -
|
Shift SW Status (4 or D)
| Shift Switch Status (4 or D)
| -
|
Shift SW Status (3 Range)
| Shift Switch Status (3 range)
| -
|
A/T Oil Temperature 1
| ATF temperature sensor value
| -
|