DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0011 | Valve timing is not adjusted in the valve timing advance range (1 trip detection logic). |
|
| P0012 | Valve timing is not adjusted in the valve timing retard range (2 trip detection logic). |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0011 or P0012 is output | A |
| DTC P0011 or P0012 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).
Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.
| Tester Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester (Click here).
Allow the engine to idle for more than 1 minute.
Drive the vehicle for more than 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0011 or P0012 is output | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Inspect the camshaft timing oil control valve assembly (Click here).
![]() |
Connect the positive (+) battery terminal to terminal 1 and the negative (-) battery terminal to terminal 2. Check the valve operation.
Reinstall the camshaft timing oil control valve assembly.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Inspect the camshaft timing gear assembly .
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
Remove the oil control valve filter.
Check that the filter is not clogged.
Reinstall the oil control valve filter.
|
| ||||
| OK | |
| 7.ADJUST VALVE TIMING |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester (Click here).
Allow the engine to idle for more than 1 minute.
Drive the vehicle for more than 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0011 or P0012 is output | B |
|
| ||||
| A | ||
| ||