STARTER > INSPECTION |
| 1. INSPECT STARTER ASSEMBLY |
Perform a pull-in test.
![]() |
Remove the nut, and then disconnect the lead wire from terminal C.
Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.
If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.
Perform a holding test.
![]() |
When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.
If the clutch pinion gear returns inward, replace the magnet starter switch assembly.
Inspect the clutch pinion gear return.
![]() |
Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.
Perform an operation test without load.
![]() |
Connect the lead wire to terminal C.
Mount the starter in a vise between aluminum plates.
Connect the battery and an ammeter to the starter as shown in the illustration.
Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.
| 2. INSPECT STARTER ARMATURE ASSEMBLY |
Check the commutator for dirt and burns on the surface.
If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
If necessary, replace the starter armature assembly.
Inspect the commutator for an open circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connector | Condition | Specified Condition |
| Segment - Segment | Always | 3.0 to 3.3 Ω |
Inspect the commutator for a short to ground.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connector | Condition | Specified Condition |
| Segment - Coil core | Always | 10 kΩ or higher |
Check the commutator circle runout.
![]() |
Place the commutator on V-blocks.
Using a dial indicator, measure the circle runout.
![]() |
Using a vernier caliper, measure the commutator diameter.
![]() |
Using a vernier caliper, measure the undercut depth of the commutator.
| 3. INSPECT STARTER BRUSH HOLDER ASSEMBLY |
![]() |
Using a vernier caliper, measure the brush length.
Check the brush holder.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A - B A - C B - D C - D | Always | 10 kΩ or higher |
| A - D B - C | Below 1 Ω |
| 4. INSPECT STARTER CLUTCH SUB-ASSEMBLY |
![]() |
Check the starter clutch pinion gear.
Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
If the result is not as specified, replace the starter clutch sub-assembly.
| 5. INSPECT MAGNET STARTER SWITCH ASSEMBLY |
Check the plunger.
![]() |
Install the plunger and spring to the switch body.
![]() |
Push in the plunger and check that it returns quickly to its original position.
If the result is not as specified, replace the magnet starter switch assembly.
Check the pull-in coil for an open circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Terminal C | Always | Below 1 Ω |
Check the holding coil for an open circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Switch body | Always | Below 2 Ω |