DTC P0617 Starter Relay Circuit High |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0617 | When conditions (a), (b) and (c) are met, a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):
|
|

| 1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to ON and when the engine is started.
| Condition | Starter Signal |
| Ignition switch ON | Close |
| Engine started | Open |
| Result | Proceed to |
| OK | A |
| NG (for Manual Transmission) | B |
| NG (for Automatic Transmission) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the ignition switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (AM2) - 7 (ST2) | LOCK | 10 kΩ or higher |
| 5 (AM2) - 7 (ST2) | START | Below 1 Ω |
| *a | Component without harness connected (Ignition Switch Assembly) |
Reconnect the ignition switch assembly connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM) |
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I8-7 (ST2) or E25-8 (STA) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the ignition switch assembly connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY [ST]) |
Disconnect the ECM connector.
Remove the starter relay (ST) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Starter relay (ST) terminal 1 or E25-8 (STA) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reinstall the starter relay (ST).
|
| ||||
| OK | ||
| ||
| 5.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the ignition switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (AM2) - 7 (ST2) | LOCK | 10 kΩ or higher |
| 5 (AM2) - 7 (ST2) | START | Below 1 Ω |
| *a | Component without harness connected (Ignition Switch Assembly) |
Reconnect the ignition switch assembly connector.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH) |
Disconnect the park/neutral position switch connector.
Disconnect the ignition switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I8-7 (ST2) or N10-4 - Body ground | Always | 10 kΩ or higher |
Reconnect the park/neutral position switch connector.
Reconnect the ignition switch assembly connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY [ST]) |
Disconnect the park/neutral position switch connector.
Remove the starter relay (ST) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Starter relay (ST) terminal 1 or N10-5 - Body ground | Always | 10 kΩ or higher |
Reconnect the park/neutral position switch connector.
Reinstall the starter relay (ST).
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the park/neutral position switch connector.
Disconnect the ECM connector.
Remove the starter relay (ST) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N10-5 or E25-8 (STA) - Body ground | Always | 10 kΩ or higher |
Reconnect the park/neutral position switch connector.
Reconnect the ECM connector.
Reinstall the starter relay (ST).
|
| ||||
| OK | ||
| ||