Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

DTC    P0430    Catalyst System Efficiency Below Threshold (Bank 2)

for Preparation Click here


DESCRIPTION

The ECM observes the waveform of the heated oxygen sensor located behind the catalyst to determine whether the catalyst performance has deteriorated.
If the catalyst is functioning normally, the waveform of the heated oxygen sensor located behind the catalyst switches back and forth between rich and lean much more slowly.
When the waveform of the heated oxygen sensor located behind the catalyst alternates frequently between rich and lean, it indicates that catalyst performance has deteriorated.

A077157E01


DTC No.
DTC Detection Condition
Trouble Area
P0420
After engine and catalyst are warmed up, and while vehicle is driven within set vehicle and engine speed range, waveform of heated oxygen sensor (bank 1 sensor 2) alternates frequently between rich and lean
(2 trip detection logic)
  1. Gas leak from exhaust system
  2. Air fuel ratio sensor (for Bank 1 Sensor 1)
  3. Heated oxygen sensor (for Bank 1 Sensor 2)
  4. Exhaust manifold RH (TWC: Front catalyst)
  5. Front exhaust pipe assembly (TWC: Rear catalyst)
P0430
After engine and catalyst are warmed up, and while vehicle is driven within set vehicle and engine speed range, waveform of heated oxygen sensor (bank 2 sensor 2) alternates frequently between rich and lean
(2 trip detection logic)
  1. Gas leak from exhaust system
  2. Air fuel ratio sensor (for Bank 2 Sensor 1)
  3. Heated oxygen sensor (for Bank 2 Sensor 2)
  4. Exhaust manifold LH (TWC: Front catalyst)
  5. Front No. 2 exhaust pipe assembly (TWC: Rear catalyst)

CATALYST LOCATION


A240423E01


CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the catalyst monitor. This is very useful for verifying the completion of a repair.


A231470E03

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the tester on.
  7. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  8. Drive the vehicle at approximately 60 km/h (38 mph) for 10 minutes or more [B].

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / DTC [C].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0420 or P0430.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [D] through [E].

  14. Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [D].

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  15. Check the DTC judgment result again [E].

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 OR P0430)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0420 or P0430 is output
    A
    P0420 or P0430 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of - 12.0% to +12.0%. The injection volume can be changed in fine gradations.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


    Tester Display (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    +12%
    Rich
    Below 3.1 V
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    -12%
    Lean
    Higher than 3.4 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    +12%
    Rich
    Higher than 0.55 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    -12%
    Lean
    Below 0.4 V

    Result:

    Status of AFS Voltage B1S1 or AFS Voltage B2S1
    Status of O2S B1S2 or O2S B2S2
    Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-way catalytic converter
    2. Gas leaks from exhaust system
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    Air fuel ratio sensor
    B
    Lean/Rich
    Lean
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leaks from exhaust system
    C
    Lean/Rich
    Rich
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leaks from exhaust system
    C
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leaks from exhaust system
    D
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leaks from exhaust system
    D

    Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.
    Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.
    Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.

  1. Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (Click here).



B
REPLACE AIR FUEL RATIO SENSOR

C
Go to step 5

D
Go to step 6
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

    OK:
    No gas leaks.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
  1. According to the DTCs output above (Check for Any Other DTCs Output), proceed to the next step referring to the table below.
    Result 
    Result
    Proceed to
    P0420 is output
    A
    P0430 is output
    B
    P0420 and P0430 are output
    A and B



B
REPLACE EXHAUST MANIFOLD LH AND FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)
A

REPLACE EXHAUST MANIFOLD RH AND FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) 

5.CHECK FOR EXHAUST GAS LEAK
  1. Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

    OK:
    No gas leaks.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK

REPLACE HEATED OXYGEN SENSOR 

6.CHECK FOR EXHAUST GAS LEAK
  1. Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

    OK:
    No gas leaks.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK

CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO