Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

DTC    P0174    System Too Lean (Bank 2)

DTC    P0175    System Too Rich (Bank 2)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
If both the short-term and long-term fuel trim values are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
When air-fuel ratio feedback is stable after warming up engine, fuel trim is considered to be in error on LEAN side
(2 trip detection logic)
  1. Air induction system
  2. Fuel injector blockage
  3. Mass air flow meter assembly
  4. Engine coolant temperature sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor circuit
  8. Air fuel ratio sensor
  9. Air fuel ratio sensor heater
  10. A/F relay
  11. Air fuel ratio sensor heater and A/F relay circuits
  12. PCV valve and hose
  13. PCV hose connections
  14. ECM
  15. Wire harness or connector
P0172
P0175
When air-fuel ratio feedback is stable after warming up the engine, fuel trim is considered to be in error on RICH side
(2 trip detection logic)
  1. Fuel injector leak or blockage
  2. Mass air flow meter assembly
  3. Engine coolant temperature sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor circuit
  8. Air fuel ratio sensor
  9. Air fuel ratio sensor heater
  10. A/F relay
  11. Air fuel ratio sensor heater and A/F relay circuits
  12. ECM

HINT:
  1. When DTC P0171 or P0174 is recorded, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is recorded, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be recorded. The MIL then illuminates.
  3. If the total of the short-term fuel trim value and long-term fuel trim value is between -35% and +52% (engine coolant temperature is more than 75°C (167°F)), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affects the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air-fuel ratio). If the average fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and sets a DTC.
Example:
The average fuel trim learning value is more than +52% or less than -35%, the ECM interprets this as a fuel system malfunction.

A197672E03


CONFIRMATION DRIVING PATTERN


A199233E70

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].
  7. With the engine warmed up, idle the engine for 2 minutes or more [C].
  8. Drive the vehicle at a speed between 60 and 100 km/h (38 and 63 mph) for 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / DTC [E].
  10. Read the pending DTCs.

    HINT:
    If a pending DTC is output, the system is malfunctioning.


WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the A/F control function provided in the Active Test. The A/F control function can help to determine whether the A/F sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the A/F control operation using the intelligent tester.

  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Start the engine and turn the tester ON.
  3. (c) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. (d) On the tester, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
  5. (e) Perform the A/F control operation with the engine idling (press the right or left button to change the fuel injection volume).
  6. (f) Monitor the voltage outputs of the A/F and heated oxygen sensors (AFS B1S1 (AFS B2S1) and O2S B1S2 (O2S B2S2)) displayed on the tester.

HINT:
  1. The A/F control operation lowers the fuel injection volume by 12.0% or increases the injection volume by 12.0%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Standard:

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1 (A/F)
+12%
Rich
Less than 3.1 V
AFS B1S1 or AFS B2S1 (A/F)
-12%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2 (heated oxygen sensor)
+12%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2 (heated oxygen)
-12%
Lean
Less than 0.4 V

NOTICE:
The air-fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E05
A151324E08
A150787E05
A150788E06
-
2
A150787E05
A150790E01
A150787E05
A150788E06
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A150787E05
A151324E08
A150787E05
A150790E01
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A150787E05
A150790E01
A150787E05
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (air-fuel ratio extremely rich or lean)

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    P0171, P0172, P0174 or P0175 is output
    A
    P0171, P0172, P0174 or P0175 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leaks in air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of - 12.0% to +12.0%. The injection volume can be changed in fine gradations.
  2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12%
Rich
Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
-12%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+12%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
-12%
Lean
Less than 0.4 V


Result:

Status of AFS Voltage B1S1 or AFS Voltage B2S1
Status of O2S B1S2 or O2S B2S2
Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition
Misfire
Suspected Trouble Area
Proceed to
Lean / Rich
Lean / Rich
Normal
-
-
A
Lean
Lean
Actual air-fuel ratio lean
May occur
  1. PCV valve and hose
  2. PCV hose connection
  3. Fuel injector assembly blockage
  4. Gas leakage from exhaust system
  5. Air induction system
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
A
Rich
Rich
Actual air-fuel ratio rich
-
  1. Fuel injector assembly leakage or blockage
  2. Gas leakage from exhaust system
  3. Ignition system
  4. Fuel pressure
  5. MAF meter
  6. ECT sensor
A
Lean
Lean / Rich
A/F sensor malfunction
-
  1. A/F sensor
B
Rich
Lean / Rich
A/F sensor malfunction
-
  1. A/F sensor
B

HINT:
Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.
Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.
Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.



B
Go to step 11
A


5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read Coolant Temp twice, when the engine is both cold and warmed up.

    OK:
    With cold engine: Same as ambient temperature
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


6.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp and MAF.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 16.9 gm/s. and 20.7 gm/s. (shift lever: N; A/C: Off).



NG
Go to step 16
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure (high or low pressure).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No exhaust gas leaks.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FOR SPARK AND IGNITION
  1. Perform a spark test.

    CAUTION:
    Always disconnect all the injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    OK:
    Sparks jump across electrode gap.



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the injection and volume.



OK
Go to step 15

NG
REPLACE FUEL INJECTOR ASSEMBLY

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A085152E37
  1. Disconnect the A35 and A36 A/F sensor connectors.

  1. Measure the resistance of the A/F sensor.

    Standard resistance:
    Bank 1 
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    -
    10 kΩ or higher
    Bank 2 
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    -
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR
OK


12.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
A150242E49
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A35-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    A36-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 21
OK


13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
A112437E04
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1 Sensor 1 
    Terminal Connection
    Specified Condition
    A35-1 (HA1A) - E16-2 (HA1A)
    Below 1 Ω
    A35-3 (A1A+) - E16-22 (A1A+)
    Below 1 Ω
    A35-4 (A1A-) - E16-30 (A1A-)
    Below 1 Ω
    A35-1 (HA1A) or E16-2 (HA1A) - Body ground
    10 kΩ or higher
    A35-3 (A1A+) or E16-22 (A1A+) - Body ground
    10 kΩ or higher
    A35-4 (A1A-) or E16-30 (A1A-) - Body ground
    10 kΩ or higher
    Bank 2 Sensor 1 
    Terminal Connection
    Specified Condition
    A36-1 (HA2A) - E16-1 (HA2A)
    Below 1 Ω
    A36-3 (A2A+) - E16-23 (A2A+)
    Below 1 Ω
    A36-4 (A2A-) - E16-31 (A2A-)
    Below 1 Ω
    A36-1 (HA2A) or E16-1 (HA2A) - Body ground
    10 kΩ or higher
    A36-3 (A2A+) or E16-23 (A2A+) - Body ground
    10 kΩ or higher
    A36-4 (A2A-) or E16-31 (A2A-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor


NEXT


15.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0171, P0172, P0174 or P0175 is output
    A
    DTC is not output
    B



B
END
A


16.CHECK HARNESS AND CONNECTOR
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.

    HINT:
    Repair any problems.


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0171, P0172, P0174 or P0175 is output
    A
    DTC is not output
    B



B
END
A


18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A112445E02
  1. Disconnect the A4 MAF meter connector.

  1. Disconnect the E15 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-3 (VG) - E15-30 (VG)
    Below 1 Ω
    A4-2 (E2G) - E15-29 (E2G)
    Below 1 Ω
    A4-3 (VG) or E15-30 (VG) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
  1. Replace the mass air flow meter sub-assembly.

    HINT:
    If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.


NEXT


20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0171, P0172, P0174 or P0175 is output
    B



B
REPLACE ECM
A

END 

21.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
A112440E04
  1. Disconnect the A35 and A36 A/F sensor connectors.

  1. Disconnect the E16 ECM connector.

  1. Remove the A/F relay from the engine room relay block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Bank 1 Sensor 1 
    Tester Connection
    Specified Condition
    A35-1 (HA1A) - E16-2 (HA1A)
    Below 1 Ω
    A35-2 (+B) - Relay block A/F relay terminal 3
    Below 1 Ω
    A35-1 (HA1A) or E16-2 (HA1A) - Body ground
    10 kΩ or higher
    A35-2 (+B) or relay block A/F relay terminal 3 - Body ground
    10 kΩ or higher
    Bank 2 Sensor 1 
    Tester Connection
    Specified Condition
    A36-1 (HA2A) - E16-1 (HA2A)
    Below 1 Ω
    A36-2 (+B) - Relay block A/F relay terminal 3
    Below 1 Ω
    A36-1 (HA2A) or E16-1 (HA2A) - Body ground
    10 kΩ or higher
    A36-2 (+B) or relay block A/F relay terminal 3 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


22.INSPECT A/F RELAY
  1. Inspect the A/F relay (Click here).



NG
REPLACE A/F RELAY
OK

CHECK ECM POWER SOURCE CIRCUIT