Home › ENGINE · 2TR-FBE › CHARGING › CHARGING SYSTEM

CHARGING SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. CHECK BATTERY CONDITION

NOTICE:
If the battery is weak or if the engine is difficult to start, perform the following procedures.

  1. Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.

  1. Check the electrolyte quantity of each cell.

    1. For maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, replace the battery.
      1. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is below 9.6 V, recharge or replace the battery.

      HINT:
      Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).

    2. For non-maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte's specific gravity.

      Standard specific gravity:
      1.25 to 1.29 at 20°C (68°F)

      1. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is below 9.6 V, recharge or replace the battery.

      HINT:
      Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).



2. INSPECT BATTERY TERMINAL AND FUSE
  1. Check that the battery terminals are not loose or corroded.
    If the terminals are corroded, clean the terminals.

  1. Measure the resistance of related fuses.

    Standard resistance:
    Below 1 Ω

    If the results are not as specified, replace the fuse as necessary.



3. INSPECT DRIVE BELT


    A058797E02
  1. Check the belt for wear, cracks or other signs of damage.
    If any of the following defects is found, replace the drive belt.

    1. The belt is cracked.
    2. The belt is worn out to the extent that the cords are exposed.
    3. The belt has chunks missing from the ribs.



    A087787E04
  1. Check that the belt fits properly in the ribbed groves.

    HINT:
    Check with your hand to confirm that the belt has not slipped out of the groove on the bottom to the pulley. If it has slipped out, replace the drive belt. Install a new drive belt correctly.



    G038478E02
  1. Check that the tensioner indicator mark is within range A shown in the illustration.
    If the mark is not within range A, replace the drive belt.



4. VISUALLY CHECK GENERATOR WIRING
  1. Check that the wiring is in good condition.
    If the wiring is damaged, repair the generator wire.



5. LISTEN FOR ABNORMAL NOISES FROM GENERATOR
  1. Check that the generator does not emit any abnormal noise while the engine is running.
    If there is abnormal noise, replace the pulley or generator.



6. CHECK CHARGE WARNING LIGHT CIRCUIT
  1. Turn the ignition switch to ON. Check that the charge warning light turns on.

  1. Start the engine and check that the light turns off.
    If the light does not operate as specified, troubleshoot the charge warning light circuit.



7. CHECK CHARGING CIRCUIT WITHOUT LOAD


  1. Check the charging circuit.



      A112985E03
    1. Keep the engine speed at 2000 rpm. Check the reading on the ammeter and voltmeter.

      Standard current:
      10 A or less

      Standard voltage:
      13.2 to 14.8 V

      If the result is not as specified, replace the generator.

      HINT:
      If the battery is not fully charged, the ammeter reading will sometimes be more than the standard current.



8. CHECK CHARGING CIRCUIT WITH LOAD
  1. With the engine running at 2000 rpm, turn on the high beam headlights and turn the heater blower switch to the HI position.

  1. Check the reading on the ammeter.

    Standard current:
    30 A or higher

    If the ammeter reading is below the standard current, replace the generator.

    HINT:
    If the battery is fully charged, the charging circuit may not operate and the ammeter reading may be below the standard current. If this is case, add more electrical load (operate the wipers, rear window defogger, etc.) and check the reading on the ammeter again.