Home › TRANSMISSION ยท A343F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > TERMINALS OF ECM

for Preparation Click here



CHECK ECM

C115871E16

HINT:
The standard voltage at each ECM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E8-30 (NSW) - E11-3 (E1)
L-Y - BR
PNP switch signal
  1. Ignition switch ON
  2. Shift lever in P or N
Below 1 V
  1. Ignition switch ON
  2. Shift lever not in P or N
11 to 14 V
E9-11 (R) - E11-3 (E1)
R-Y - BR
R shift position switch signal
  1. Ignition switch ON
  2. Shift lever in R
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in R
Below 1 V
E9-19 (3) - E11-3 (E1)
G-O - BR
3 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 3
Below 1 V
E9-10 (2) - E11-3 (E1)
L - BR
2 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 2
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 2
Below 1 V
E9-9 (L) - E11-3 (E1)
G-R - BR
L shift position switch signal
  1. Ignition switch ON
  2. Shift lever in L
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in L
Below 1 V
E10-9 (S1) - E11-3 (E1)
B-W - BR
S1 solenoid signal
1st or 2nd gear
11 to 14 V
3rd or 4th gear
Below 1 V
E10-8 (S2) - E11-3 (E1)
B-R - BR
S2 solenoid signal
2nd or 3rd gear
11 to 14 V
1st or 4th gear
Below 1 V
E10-12 (SLT+) - E10-13 (SLT-)
B-L - B-Y
SLT solenoid signal
Engine idling
Pulse generation
E10-11 (SL) - E11-3 (E1)
L-Y - BR
SL solenoid signal
Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)
Pulse generation
(See waveform 1)
Vehicle driving under look-up condition
11 to 14 V
E11-22 (THOC) - E11-28 (E2)
W-L - BR
ATF temperature sensor signal
ATF temperature: 115°C (239°F) or higher
Below 1.5 V
E10-35 (SP2+) - E10-27 (SP2-)
G - R
Speed sensor SP2 signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 2)
E10-34 (NC0+) - E10-26 (NC0-)
V - P
Speed sensor NC0 signal
Engine idling
(shift lever in P or N)
Pulse generation
(See waveform 3)
E8-11 (L4) - E11-3 (E1)
G-W - BR
L4 position signal
  1. Ignition switch ON
  2. Transfer in L4
Below 1 V
  1. Ignition switch ON
  2. Transfer not in L4
11 to 14 V
E9-8 (SPD) - E11-3 (E1)
V-R - BR
Speed signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 4)
E9-4 (STP) - E11-3 (E1)
G-W - BR
STP light switch signal
  1. Ignition switch ON
  2. Brake pedal is depressed
11 to 14 V
  1. Ignition switch ON
  2. Brake pedal is released
Below 1 V
E8-12 (STA) - E11-3 (E1)
B-Y - BR
Starter signal
Cranking
6 V or more
E8-23 (TFN) - E11-3 (E1)
W-G - BR
N shift position switch signal
  1. Ignition switch ON
  2. Transfer in N
Below 1 V
  1. Ignition switch ON
  2. Transfer not in N
11 to 14 V
E9-13 (SIL) - E11-3 (E1)
R-Y - BR
Terminal SIL of DLC3
Connect intelligent tester to DLC3
Pulse generation
E9-35 (WFSE) - E11-3 (E1)
W - BR
Terminal SIL of DLC3
Ignition switch ON
11 to 14 V


    C170572E01
  1. Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    E10-11 (SL) - E11-3 (E1)
    10 V/DIV., 100 msec./DIV.
    Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)



  2. C170571E02
  3. Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    E10-35 (SP2+) - E10-27 (SP2-)
    2 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)



  4. C170570E01
  5. Using an oscilloscope, check waveform 3.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    E10-34 (NC0+) - E10-26 (NC0-)
    5 V/DIV., 0.5 msec./DIV.
    Engine idling (shift lever in P or N)



  6. C170574E01
  7. Using an oscilloscope, check waveform 4.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    E9-8 (SPD) - E11-3 (E1)
    5 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)