AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| N Range Status | Shift lever N status/ ON or OFF |
| - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/ ON or OFF |
| - |
| SPD (NC0) | Input shaft speed/ Min.: 0 rpm Max.: 12750 rpm |
| Data is displayed in increments of 50 rpm. |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) | - |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (2 Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (L Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (N, P Range) Supported | Status of PNP switch (N or P) supported/ Supp or Unsupp | - | - |
| Shift SW Status (N, P Range) | PNP switch status/ ON or OFF |
| - |
| Shift SW Status (3 Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| A/T Oil Temperature 3 | ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If the value is -40°C (-40°F) or 215°C (419°F), the ATF temperature sensor circuit is open or shorted. |
| Lock Up | Lock-up/ ON or OFF |
| - |
| Lock Up Solenoid Status | Shift solenoid SL status/ ON or OFF |
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd or 4th |
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| - |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate the shift solenoid valve SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
| Activate the Solenoid (S1) | Operate the shift solenoid valve S1 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S2) | Operate the shift solenoid valve S2 | ON or OFF | [Vehicle Condition]
|
| Activate the Lock Up | Control shift solenoid valve SL to set automatic transmission to lock-up | ON or OFF | Possible to check shift solenoid valve SL operation. [Vehicle Condition]
|
| Activate the Solenoid (SL) | Operate the shift solenoid valve SL | ON or OFF | [Vehicle Condition]
|
| Control the Shift Position | Operate shift solenoid valves and set each shift position |
| Possible to check operation of the shift solenoid valves. [Vehicle Condition] 50 km/h (30 mph) or less |