Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)

DTC    P0711    Transmission Fluid Temperature Sensor "A" Performance

for Preparation Click here


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the ATF temperature into a resistance value which is input into the ECM.
The ECM applies a voltage to the temperature sensor through ECM terminal THO1.
The sensor resistance changes with the ATF temperature.
One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature becomes higher.
The ECM calculates the ATF based on the voltage signal.

DTC Code
DTC Detection Condition
Trouble Area
P0711
  1. Both (a) and (b) are detected (2 trip detection logic):
    1. Intake air and engine coolant temperatures are more than -10°C (-14°F) at engine start
    2. After normal driving for over 21 min. and 9 km (6 miles) or more, ATF temperature is less than 20°C (68°F)
No. 1 ATF temperature sensor

MONITOR DESCRIPTION

This DTC indicates that there is a problem with output from the ATF temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects opens or shorts in the ATF temperature circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, and illuminates the MIL.

WIRING DIAGRAM


C120654E02


INSPECTION PROCEDURE

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Warm up the engine.
  2. Turn the ignition switch OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch ON and push the tester main switch ON.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/T Oil Temperature 1
No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
  1. After stall test:
    Approximately 80°C (176°F)
  2. Equal to ambient temperature during cold soak
If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is opened or short circuited

CAUTION:
In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
  1. When DTC P0712 is output and the intelligent tester output is 150°C (302°F) or more, there is a short circuit.
  2. When DTC P0713 is output and the intelligent tester output is -40°C (-40°F), there is an open circuit.
    Measure the resistance between terminal THO1 (OT) and the body ground.


Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit

HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is set in approximately 0.5 seconds.
It is not necessary to inspect the circuit when P0711 is set.

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0711)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and push the intelligent tester main switch ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Current or Pending.

  1. Read the DTCs using the intelligent tester.

    Result:
    Display (DTC output)
    Proceed to
    Only P0711 is output
    A
    P0711 and other DTCs
    B

    HINT:
    If any other codes besides P0711 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.CHECK TRANSMISSION FLUID LEVEL

OK:
Automatic transmission fluid level is correct.



NG
ADD FLUID
OK

REPLACE TRANSMISSION WIRE