Home › TRANSMISSION · A343E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2TR-FBE)

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Conditions
Trouble Areas
P0705
2 or more switches are ON simultaneously for P (NSW), R, N (NSW), D, 2 or L positions (2 trip detection logic)
  1. Park/neutral position switch circuit
  2. Shift lock control ECU (Shift lock control unit assembly)
  3. Park/neutral position switch
  4. ECM

MONITOR DESCRIPTION

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is on P or N.
When the park/neutral position switch sends more than one signal at a time from switch positions P, R, N, D, 2 or L, the ECM interprets this as a fault in the switch. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM


C169725E18


INSPECTION PROCEDURE


HINT:
Using the Data List of the intelligent tester allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON and push the tester main switch on.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In P or N
  2. OFF: Not in P or N
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In R
  2. OFF: Not in R
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (2 Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In 2
  2. OFF: Not in 2
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (L Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In L
  2. OFF: Not in L
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (3 Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In 3
  2. OFF: Not in 3
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

NOTICE:
In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

1.INSPECT PARK/NEUTRAL POSITION SWITCH


    C146745E17
  1. Disconnect the N1 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    4 (B) - 5 (L)
    Not in P or N
    10 kΩ or higher
    1 (RL) - 2 (RB)
    R
    Below 1 Ω
    1 (RL) - 2 (RB)
    Not in R
    10 kΩ or higher
    2 (RB) - 7 (DL)
    D
    Below 1 Ω
    2 (RB) - 7 (DL)
    Not in D
    10 kΩ or higher
    2 (RB) - 3 (2L)
    2
    Below 1 Ω
    2 (RB) - 3 (2L)
    Not in 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    L
    Below 1 Ω
    2 (RB) - 8 (LL)
    Not in L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH
OK


2.INSPECT SHIFT LOCK CONTROL ECU


    C170575E01
  1. Disconnect the S30 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    9 (NSSD) - 3 (AT3)
    D
    10 kΩ or higher
    9 (NSSD) - 3 (AT3)
    3
    Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY)
OK


3.CHECK WIRE HARNESS (ECM - BATTERY)
  1. Disconnect the E22 and E25 ECM connectors.



    C215341E04
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below

    Standard Voltage:
    Tester Connection
    Shift Lever Position
    Specified Condition
    E25-24 (NSW) - Body ground
    P or N
    Below 1 V
    E25-24 (NSW) - Body ground
    Not in P or N
    11 to 14 V
    E22-17 (R) - Body ground
    R
    11 to 14 V*
    E22-17 (R) - Body ground
    Not in R
    Below 1 V
    E25-23 (3) - Body ground
    D
    11 to 14 V
    E25-23 (3) - Body ground
    Not in D
    Below 1 V
    E22-15 (2) - Body ground
    2
    11 to 14 V
    E22-15 (2) - Body ground
    Not in 2
    Below 1 V
    E22-25 (L) - Body ground
    L
    11 to 14 V
    E22-25 (L) - Body ground
    Not in L
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM