Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

The Air-fuel Ratio (A/F) sensor generates a voltage* in response to the actual air-fuel ratio. The sensor output voltage provides feedback to the ECM. The ECM uses the feedback to control the air-fuel ratio. Using the sensor output voltage, the ECM determines the deviation from the stoichiometric air-fuel ratio, and regulates the injection time. If the A/F sensor is malfunctioning, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is equipped with a heater which heats the zirconia element. The heater is also controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), a current flows to the heater to heat the sensor to facilitate the accurate detection of oxygen concentration.
The A/F sensor is a planar type. The heat of the heater is conducted to the zirconia element through the alumina, accelerating sensor activation.
To obtain a high purification rate of carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) in the exhaust gas, the Three-Way Catalytic Converter (TWC) is used. The TWC is most efficient when the air-fuel ratio is maintained near the stoichiometric air-fuel ratio.

HINT:
  1. *: The voltage value changes inside the ECM only.
  2. These DTCs are related to the A/F sensor.


DTC No.
DTC Detection Condition
Trouble Area
P2237
Open in the circuit between terminals AF+ and AF- of the A/F sensor while engine is running
(2 trip detection logic)
  1. Open in Air Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. Air Fuel Ratio (A/F) sensor (sensor 1)
  3. ECM
P2238
  1. Condition (a) or (b) continues for 5.0 seconds or more:
    (2 trip detection logic)
    (a) AF+ is 0.5 V or less
    (b) (AF+) - (AF-) is 0.1 V or less
  1. A/F sensor admittance: Less than 0.022 1/Ω
    (2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2239
Condition (a) or (b) continues for 5.0 seconds or more:
(2 trip detection logic)
(a) AF+ is more than 4.5 V
(b) (AF+) - (AF-) is more than 0.8 V
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2252
AF- is 0.5 V or less for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2253
AF- is more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM

WIRING DIAGRAM


A192075E01


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be found by performing the Active Test / Control the Injection Volume for A/F Sensor operation. The Control the Injection Volume for A/F Sensor operation can determine if the A/F sensor, heated oxygen sensor or other potential trouble areas are malfunctioning or not.

(a) Perform Active Test using the intelligent tester.

HINT:
The Control the Injection Volume for A/F Sensor operation lowers the injection volume by 12.5% or increases the injection volume by 12.5%.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the intelligent tester ON.
  3. Warm up the engine by running the engine at 2500 rpm for approximately 90 seconds.
  4. On the intelligent tester, select the following menu items: Powertrain / Engine and ECT / Active Test /Control the Injection Volume for A/F Sensor.
  5. Select the following monitor items: AFS Voltage B1S1 and O2S B1S2.
  6. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the right or left button).

HINT:
  1. The "Control the Injection Volume for A/F Sensor" operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1
(A/F)
+12.5%
Rich
Less than 3.0 V
AFS Voltage B1S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1S2
(HO2)
+12.5%
Rich
More than 0.55 V
O2S B1S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The A/F sensor output has a few seconds of delay and the heated oxygen sensor output has about 20 seconds of delay at maximum.


Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E08
A151324E01
A150787E08
A150788E01
-
2
A150787E08
A150790E01
A150787E08
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E08
A151324E01
A150787E08
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E08
A150790E01
A150787E08
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
The following "Control the Injection Volume for A/F Sensor" procedure enables the technician to check and graph the output voltage of both A/F sensor and heated oxygen sensor.
To display the graph, select the following menu items on the tester: View / Line graph.

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check the conditions that would cause the engine to run with a rich air-fuel mixture.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check the conditions that would cause the engine to run with a lean air-fuel mixture.

1.CHECK WIRE HARNESS (A/F SENSOR - ECM)
G038637E22
  1. Disconnect the A5 A/F sensor connector.

  1. Disconnect the E11 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A5-1 (HA1A) - E11-1 (HA1A)
    Below 1 Ω
    A5-3 (A1A+) - E11-21 (A1A+)
    Below 1 Ω
    A5-4 (A1A-) - E11-31 (A1A-)
    Below 1 Ω
    A5-1 (HA1A) or E11-1 (HA1A) - Body ground
    10 kΩ or higher
    A5-3 (A1A+) or E11-21 (A1A+) - Body ground
    10 kΩ or higher
    A5-4 (A1A-) or E11-31 (A1A-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor.


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine.

  1. Allow the engine idle for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read pending DTCs.

    Result:
    Result
    Proceed to
    No DTC is output
    A
    P2237, P2238, P2239, P2252 or P2253 is output
    B



B
REPLACE ECM
A

END