ECD SYSTEM (for i-ART) > SYSTEM DESCRIPTION |
| ENGINE CONTROL SYSTEM |

| *1 | ECM | *2 | Fuel Supply Pump Assembly |
| *3 | Suction Control Valve | *4 | Common Rail Assembly |
| *5 | Pressure Discharge Valve | *6 | EDU Relay |
| *7 | VSV for EGR Bypass Valve | *8 | Intercooler |
| *9 | Intake Air Temperature Sensor (Turbo) | *10 | Diesel Throttle Body Assembly |
| *11 | Injector Driver | *12 | Intake Air Temperature Sensor (Built Into Mass Air Flow Meter) |
| *13 | Manifold Absolute Pressure Sensor | *14 | Mass Air Flow Meter |
| *15 | EGR Cooler | *16 | Injector Assembly |
| *17 | Glow Plug | *18 | Glow Plug Controller |
| *19 | Electric EGR Control Valve Assembly | *20 | Engine Coolant Temperature Sensor |
| *21 | No. 1 Vacuum Switching Valve (for Swirl Control Valve) | *22 | No. 2 Vacuum Switching Valve (for Swirl Control Valve) |
| *23 | DC Motor, Nozzle Vane Position Sensor | *24 | Turbocharger Sub-assembly |
| *25 | Camshaft Position Sensor | *26 | Crankshaft Position Sensor |
| *27 | Accelerator Pedal Position Sensor | - | - |
| i-ART SYSTEM |

| *1 | Piezo Actuator | *2 | No. 1 Piston |
| *3 | No. 2 Piston | *4 | Three-Way Valve |
| *5 | Nozzle Needle | *6 |
|
| *a | Injector Assembly Cross Section Diagram | - | - |
| COMMON RAIL SYSTEM DESCRIPTION |
Common rail system:
The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power while suppressing engine vibration and noise.
This system stores fuel in the common rail, which has been pressurized and supplied by the fuel supply pump assembly. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
The ECM, using the injector driver, provides an electric current to the piezo actuator in each injector to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor built into each injector. The ECM causes the fuel supply pump assembly to supply the fuel necessary to obtain the target fuel pressure.
In addition, this system uses a piezo actuator inside each injector to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
The common rail system allows for a two stage fuel injection process. In order to soften combustion shock, this system performs "pilot-injection" prior to the main fuel injection. This helps to reduce engine vibration and noise.

| *1 | Common Rail Assembly | *2 | Pressure Discharge Valve |
| *3 | Fuel Supply Pump Assembly | *4 | Suction Control Valve |
| *5 | Injector Driver | *6 | ECM |
| *7 | Injector Assembly | *8 | Fuel Cooler |
| *9 | Fuel Filter | *10 | Fuel Filter (w/ Secondary Fuel Filter) |
| *11 | Fuel Tank | *12 | Fuel Check Valve |
![]() | High Pressure Fuel Line | ![]() | Return Fuel Line |
![]() | Suction Fuel Line | - | - |
Common rail system components:
| Component | Description |
| Common rail assembly | Stores high-pressure fuel produced by fuel supply pump assembly |
| Fuel supply pump assembly |
|
| Injector assembly | Injects fuel to combustion chamber based on signals from ECM |
| Fuel pressure sensor (Built into injector assembly) | Monitors internal fuel pressure of injector assembly and sends signals to ECM |
| Pressure discharge valve | Based on signals from ECM, opens valve when sudden deceleration occurs, or when ignition switch is off to prevent fuel pressure from becoming too high. |
| Suction control valve | Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure |
| Check valve | Keeps pressure that discharges from injector assembly |
Diagnostic trouble code (DTC) table for the common rail system:
| Trouble Area | Malfunction | DTC No. |
| Injector assembly | Open or short in injector circuit | P0093*, P0201, P0202, P0203, P0204, P062D, P029D, P02A1, P02A5, P02A9 |
| Stuck open | P0093, P029D, P02A1, P02A5, P02A9 | |
| Stuck closed | - | |
| Fuel pressure sensor (Built into injector assembly) | Open or short in fuel pressure sensor circuit or pressure sensor range/performance | P13A1, P13A2, P13A6, P13A7, P13AB, P13AC, P13B1, P13B2 P13E1, P13E2, P13E6, P13E7 P13A3, P13A8, P13AD, P13B3 |
| Pressure discharge valve | Open or short in pressure discharge valve circuit | P0088*, P0093*, P1229*, P1271, P1272 |
| Stuck open | P0093 | |
| Stuck closed | P0088*, P1272 | |
| Suction control valve | Open or short in suction control valve circuit | P0627, P1229, P0088* |
| Stuck open | P0088*, P1229 | |
| Injector driver | Faulty injector driver | P0093*, P0201*, P0202*, P0203*, P0204*, P062D*, P1271*, P1272*, P029D*, P02A1*, P02A5*, P02A9* |
| Common rail system (Fuel system) | Fuel leaks in high-pressure area | P0093 |
Diagnostic trouble code description for the common rail system:
| DTC No. | Description |
| P0088 | Internal fuel pressure too high (220000 kPa [2243 kgf/cm2, 31900 psi] or more) |
| P0093 | Fuel leaks in high-pressure areas |
| P0201 to P0204 | Open or short in No. 1 to No. 4 injector circuit |
| P029D | Cylinder 1 - Injector Leaking |
| P02A1 | Cylinder 2 - Injector Leaking |
| P02A5 | Cylinder 3 - Injector Leaking |
| P02A9 | Cylinder 4 - Injector Leaking |
| P0627 | Open or short in suction control valve circuit |
| P062D | Open or short in injector driver or injector circuit |
| P1229 | Fuel over-feed |
| P1271 | Open or short in pressure discharge valve circuit |
| P1272 | Pressure discharge valve stuck close |
| P13A1 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13A2 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13A6 | Open or short in No. 2 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13A7 | Open or short in No. 2 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13AB | Open or short in No. 3 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13AC | Open or short in No. 3 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13B1 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13B2 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13E1 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Main CPU) |
| P13E2 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Main CPU) |
| P13E6 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Main CPU) |
| P13E7 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Main CPU) |
| P13A3 | No. 1 injector assembly (fuel pressure sensor) circuit range/performance |
| P13A8 | No. 2 injector assembly (fuel pressure sensor) circuit range/performance |
| P13AD | No. 3 injector assembly (fuel pressure sensor) circuit range/performance |
| P13B3 | No. 4 injector assembly (fuel pressure sensor) circuit range/performance |
| INJECTION CONTROL SYSTEM DESCRIPTION |

| FUEL SUPPLY PUMP OPERATION SYSTEM DESCRIPTION |

| SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION |
Small opening of the suction control valve:
When the opening of the suction control valve is small, the volume of supplied fuel is small.
The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum.
Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).

Large opening of the suction control valve:
When the opening of the suction control valve is large, the volume of supplied fuel is large.
If the plunger stroke is full, the suction volume becomes large because of the wide path.
Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).
