Home › ENGINE ยท 2TR-FBE › FUEL › FUEL SYSTEM

FUEL SYSTEM > PRECAUTION

for Preparation Click here


CAUTION:
  1. Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.
  2. Do not smoke or be near an open flame when working on the fuel system.
  3. Keep gasoline away from rubber or leather parts.


1.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Remove the driver side scuff plate.

    1. Using a screwdriver, detach the 7 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Using a clip remover, detach the 3 clips and remove the scuff plate.



  3. A116042
  4. Turn up the floor carpet and disconnect the joining connector, as shown in the illustration.

    HINT:
    This connector has the lines of the fuel pump and rear speed sensor.

  5. Connect the cable to the negative (-) battery terminal.

  6. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC C0210/33 and DTC C0215/34 (rear speed sensor circuit) and DTC P0171/25 (system too lean) may be set.

  7. Crank the engine again, and then check that the engine does not start.

  8. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

  9. Connect the fuel pump connector.

  10. Install the driver side scuff plate.


2.FUEL SYSTEM
  1. When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

    1. Discharge the fuel system pressure (See above procedure).

    2. Put a container under the connection.

    3. Disconnect the fuel pump tube.

    4. Drain the fuel remaining inside the fuel pump tube.

    5. To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.



  2. A111059E01
  3. Observe these precautions when removing and installing the injector.

    1. Never reuse the O-rings.

    2. When placing a new O-ring on the injector, take care not to damage it in any way.

    3. Coat new O-rings with grease or gasoline before installing. Never use engine, gear or brake oil.



  4. A099424E02
  5. Install the injector to the delivery pipe and cylinder head, as shown in the illustration. Before installing the injector, be sure to apply grease or gasoline on the place where the delivery pipe touches the O-ring of the injector.



  6. A099425E04
  7. Observe these precautions when disconnecting the fuel tube connector (quick type).

    1. Fuel hose connector cover type:
      Detach the lock claw by lifting up the cover, as shown in the illustration.



    2. A099426E03
    3. Fuel pipe clamp type:
      Remove the fuel pipe clamp from the fuel tube connector.

    4. Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.



    5. A088336E04
    6. If the connector and the pipe are stuck, pinch the connector, push and pull the pipe to disconnect the pipe and pull it out.

      NOTICE:
      Do not use any tools.

    7. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.

    8. To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.



  8. A071366E09
  9. Observe these precautions when connecting the fuel tube connector (quick type).

    1. Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil on the tip of the pipe.



    3. A071366E10
    4. After having finished the connection, try to pull apart the pipe and the connector and confirm that they are securely connected.



    5. A099426E02
    6. Fuel pipe clamp type:
      Install the fuel pipe clamp to the connector.



    7. A099425E05
    8. Fuel hose connector cover type:
      Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.


3.FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


    A239219
  1. Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube assembly with pump and gauge. Doing so will cause reassembly of the fuel suction tube assembly with pump and gauge to be impossible as the tube is welded to the plate.


4.CHECK FOR FUEL LEAKS
  1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (Click here).