FUEL TANK > INSTALLATION |
| 1. INSTALL FUEL TANK TO FILLER PIPE HOSE |
Install the fuel tank to filler pipe hose to the fuel tank.
| 2. INSTALL FUEL TANK BREATHER HOSE |
Install the fuel tank breather hose to the fuel tank.
| 3. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
Apply a light coat of gasoline or grease to a new gasket, and install the gasket to the fuel tank.
Install the fuel suction with pump and gauge tube to the fuel tank.
| 4. INSTALL FUEL PUMP GAUGE RETAINER |
Set the fuel pump gauge retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.
![]() |
Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.
While pressing SST (claws) against the fuel pump gauge retainer ribs securely, install the 4 bolts.
Install SST (handle).
![]() |
Using SST, tighten the retainer until the mark on the retainer aligns with mark A on the fuel tank as shown in the illustration.
Install the fuel tank return tube and fuel tank main tube to the fuel tank.
Install the 2 fuel tank tubes with the 2 tube joint clips.
![]() |
| 5. INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY |
Install the No. 1 fuel evaporation tube.
| 6. INSTALL NO. 1 FUEL TANK CUSHION |
Install 3 new fuel tank cushions.
| 7. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY |
![]() |
Install the No. 1 fuel tank protector with the 5 clips and 2 nuts.
| 8. INSTALL FUEL TANK ASSEMBLY |
Set a engine lifter to the fuel tank.
Lift up the engine lifter.
![]() |
Fold back the 2 cushion rubbers.
Connect the 4 harness clips and fuel pump connector to the fuel tank.
Install the 3 fuel tank bands with the 3 pins and 3 clips.
Connect the 3 fuel tank bands with the 3 bolts.
| 9. INSTALL FUEL TANK FILLER PIPE |
Install the filler pipe with the bolt and nut.
| 10. CONNECT FUEL TANK TO FILLER PIPE HOSE |
Connect the fuel tank to filler pipe hose to the fuel tank filler pipe.
| 11. CONNECT FUEL TANK BREATHER HOSE |
Attach the breather hose to the 2 clamps.
Connect the fuel tank breather hose to the fuel tank filler pipe.
| 12. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE |
![]() |
Connect the fuel tank return tube connector to the pipe. Then connect the fuel tank main tube connector to the pipe. Push the 2 tube connectors into the pipe until the tube connector makes a "click" sound.

Connect the vent line hose to the fuel pipe.
| 13. INSTALL NO. 3 FUEL TUBE CLAMP |
Install the 2 tube clamps to the fuel tube.
| 14. INSTALL FUEL TANK PROTECTOR |
Install the fuel tank protector with the 4 nuts.
| 15. INSTALL FUEL TANK CAP ASSEMBLY |
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. INSPECT FOR FUEL LEAK (for Fuel Main Tank) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Push the intelligent tester main switch on.
Select the Active Test and enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check for fuel leaks.
Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.
If there are fuel leaks, repair or replace parts as necessary.