FUEL TANK (w/o EGR System) > INSTALLATION |
| 1. INSTALL FUEL TANK TO FILLER PIPE HOSE |
Install the fuel tank to filler pipe hose to the fuel tank.
| 2. INSTALL FUEL TANK BREATHER HOSE |
Install the fuel tank breather hose to the fuel tank.
| 3. INSTALL FUEL TANK VENT TUBE SUB-ASSEMBLY |
Apply a light coat of gasoline or grease to a new gasket, and install it to the fuel tank.
Install the fuel tank vent tube to the fuel tank.
Set the fuel pump gauge retainer on the fuel tank. While holding the fuel tank vent tube, tighten the fuel pump gauge retainer one complete turn by hand.
![]() |
Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.
| *1 | SST (Plate) |
| *2 | SST (Claw) |
| *3 | Rib |
While pressing SST (claws) to the fuel pump gauge retainer ribs securely, install the 4 bolts.
Install SST (handle).
![]() |
Using SST, tighten the fuel pump gauge retainer until the mark on the fuel pump gauge retainer aligns with mark A on the fuel tank, as shown in the illustration.
| *1 | Retainer Side Mark |
| *2 | Fuel Tank Side Mark |
Install the fuel tank return tube and fuel tank main tube to the fuel tank.
Install the 2 fuel tank tubes with the 2 tube joint clips.
![]() |
| *1 | Fuel Tube Joint |
| *2 | Fuel Tube |
| *3 | O-Ring |
| *4 | Tube Joint Clip |
| *a | CORRECT |
| *b | INCORRECT |
| 4. INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY |
| 5. INSTALL NO. 1 FUEL TANK CUSHION |
| 6. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY |
![]() |
Install the No. 1 fuel tank protector with the 5 clips.
| 7. INSTALL FUEL TANK ASSEMBLY |
Set the fuel tank on an engine lifter and raise the fuel tank.
Fold back approximately half of each cushion so that the wire harness can be installed in the step below.
![]() |
Attach the wire harness to the 4 clamps and connect the fuel sender gauge connector.
Install the 2 fuel tank bands with the 2 pins and 2 clips.
Connect the 2 fuel tank bands with the 2 bolts.
| 8. CONNECT FUEL TANK TO FILLER PIPE HOSE |
Connect the fuel tank to filler pipe hose to the fuel tank filler pipe.
| 9. CONNECT FUEL TANK BREATHER HOSE |
Connect the fuel tank breather hose to the fuel tank filler pipe.
Attach the fuel tank breather hose to the 2 clamps.
| 10. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE |
| 11. INSTALL NO. 1 FUEL TANK PROTECTOR |
Install the No. 1 fuel tank protector with the 4 nuts.
| 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 13. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs.
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs.
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 14. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.