Home › ENGINE ยท 2KD-FTV › FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE NO. 1 FUEL TANK PROTECTOR


    A116046
  1. Remove the 4 nuts and No. 1 fuel tank protector.



4. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE
  1. Disconnect the fuel tank main tube and fuel tank return tube.



5. DISCONNECT FUEL TANK BREATHER HOSE


    A191366
  1. Disconnect the fuel tank breather hose from the fuel tank filler pipe.

  1. Detach the fuel tank breather hose from the 2 clamps.



6. DISCONNECT FUEL TANK TO FILLER PIPE HOSE
  1. Disconnect the fuel tank to filler pipe hose from the fuel tank filler pipe.



7. REMOVE FUEL TANK ASSEMBLY
  1. Place an engine lifter under the fuel tank.



    A116049
  1. Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.

  1. Slightly lower the engine lifter.

    NOTICE:
    Be careful not to cut the wiring.



    A116059E04
  1. Fold back approximately half of each cushion so that the wire harness can be removed in the step below.
    Text in Illustration 
    *1
    Fuel Tank Cushion
    *2
    Wire Harness
    *3
    Fuel Tank



    A272879E01
  1. Detach the wire harness from the 4 clamps shown in the illustration.
    Text in Illustration 
    *1
    Claw

    HINT:
    Detach the claws of the clamps labeled A in the illustration to detach the wire harness.

  1. Disconnect the fuel sender gauge connector.



8. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    A197465E01
  1. Using needle-nose pliers, remove the 5 clips shown in the illustration, and then remove the No. 1 fuel tank protector.



9. REMOVE NO. 1 FUEL TANK CUSHION


    A116062
  1. Remove the 2 fuel tank cushions from the fuel tank.
    Text in Illustration 
    V100155
    Fuel Tank Cushion



10. REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    A197374
  1. Remove the No. 1 fuel evaporation tube.



11. REMOVE FUEL PUMP GAUGE RETAINER


    A099441E01
  1. Remove the 2 tube joint clips and pull out the fuel tank return tube and fuel tank main tube.

    NOTICE:
    A060575E14
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend or twist the nylon tube.
    5. Protect the disconnected parts by covering them with plastic bags and tape after disconnecting the fuel tubes.

    Text in Illustration 
    *1
    Fuel Tube Joint
    *2
    Fuel Tube
    *3
    O-Ring
    *4
    Tube Joint Clip

  1. Remove the fuel tank return tube and fuel tank main tube from the fuel tank.



    A246112E02
  1. Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.

    SST
    09808-14030  
    Text in Illustration 
    *1
    SST (Plate)
    *2
    SST (Claw)
    *3
    Rib

    HINT:
    1. Be sure to use 4 SST (claws) as shown in the illustration.
    2. Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.

  1. While pressing SST (claws) to the fuel pump gauge retainer ribs securely, install the 4 bolts.

    HINT:
    Install SST while pressing SST (claws) against the fuel pump gauge retainer (towards the center of SST).

  1. Install SST (handle).



    A241650E02
  1. Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to loosen the fuel pump gauge retainer.

    SST
    09808-14030  

    NOTICE:
    1. When the fuel pump gauge retainer is loosened, be careful as the fuel tank vent tube will spring upward from the force of the spring.
    2. Clean the fuel tank vent tube before this operation.
    3. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    4. Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
    5. Make sure to rotate SST (handle) horizontally. If SST (handle) is rotated at an angle, SST may come off.
    6. Do not spin SST too fast or use an impact wrench as this may result in damage to components.
    7. If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.

    HINT:
    The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.

  1. Remove the fuel pump gauge retainer.



12. REMOVE FUEL TANK VENT TUBE SUB-ASSEMBLY
  1. Remove the fuel tank vent tube from the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.



13. REMOVE FUEL TANK BREATHER HOSE
  1. Remove the fuel tank breather hose from the fuel tank.



14. REMOVE FUEL TANK TO FILLER PIPE HOSE
  1. Remove the fuel tank to filler pipe hose from the fuel tank.