Home › ENGINE ยท 2TR-FBE › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY
(Click here)


2. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with bolts.

    NOTICE:
    1. Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
    2. With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



3. REMOVE IGNITION COIL ASSEMBLY


A111720
  1. Disconnect the 4 ignition coil connectors.

  1. Remove the 4 bolts and pull out the 4 ignition coils.



4. REMOVE SPARK PLUG
  1. Using a 16 mm plug wrench, remove the 4 spark plugs.



5. REMOVE PCV PIPE
  1. Remove the bolt and PCV pipe.



6. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
  1. Disconnect the throttle position sensor and control motor connector.

  1. Disconnect the 2 water by-pass hoses.



    A086829E01
  1. Remove the 2 bolts, 2 nuts and throttle body with motor.

  1. Remove the gasket from the intake manifold.



7. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

CAUTION:
Be careful not to drop the injectors when removing the delivery pipe.



    A237738
  1. Disconnect the 4 clamps and wire harness from the delivery pipe.

  1. Disconnect the vacuum hose.



    A237739
  1. Disconnect the 4 injector connectors.

  1. Remove the 2 bolts and fuel delivery pipe together with the fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

  1. Remove the 2 No. 1 delivery pipe spacers.

  1. Remove the 4 injector vibration insulators.



    G038847E01
  1. Using 2 screwdrivers, pry out the 4 spacers from the cylinder head.

    HINT:
    Tape the screwdriver tips before use.

  1. Remove the 4 O-rings.



8. REMOVE FUEL INJECTOR ASSEMBLY


    G034904E01
  1. Pull out the 4 fuel injectors from the delivery pipe.

  1. Remove the 4 O-rings from the 4 fuel injectors.



9. REMOVE INTAKE MANIFOLD


    A237732
  1. Disconnect the vacuum hose and fuel hose.

  1. Disconnect the purge line hose and purge VSV connector.

  1. Remove the 5 bolts, 2 nuts, intake manifold and gasket.



10. REMOVE GENERATOR ASSEMBLY
  1. Detach the terminal cap.



    A099681E03
  1. Remove the nut, bolt and disconnect the generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



11. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET


    A099203E02
  1. Remove the 5 bolts and No. 1 compressor mounting bracket.



12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A099636E02
  1. Remove the 3 bolts and tensioner.



13. REMOVE WATER INLET


A099676E01
  1. Disconnect the power steering pump connector.



    A226811
  1. Remove the 2 nuts, bolt and water inlet.

  1. Remove the gasket from the timing chain cover.



14. REMOVE THERMOSTAT
  1. Remove the thermostat from the timing chain cover.

  1. Remove the gasket from the thermostat.



15. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


A222362E01
  1. Remove the bolt, pulley and spacer.



16. REMOVE NO. 1 WATER BY-PASS PIPE


    A222413
  1. Remove the 2 nuts, water by-pass pipe and gasket.



17. REMOVE OIL FILLER CAP SUB-ASSEMBLY
  1. Remove the oil filler cap from the head cover.



18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    G035202E05
  1. Remove the 19 bolts, 2 nuts, cover and 2 gaskets.



19. REMOVE CAMSHAFT POSITION SENSOR


    A099146E01
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



20. REMOVE CRANKSHAFT PULLEY


G038864E13
  1. Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the No. 1 bearing cap, as shown in the illustration.



    A099211E08
  1. Using SST, loosen the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G035121E07
  1. Using SST, remove the pulley bolt and pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



21. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove the drain plug and gasket.



    A099214E02
  1. Remove the 20 bolts and 2 nuts.



    A099215E09
  1. Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan.

    NOTICE:
    Be careful not to damage the contact surface of the oil pans.



22. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the bolt, 2 nuts, oil strainer and gasket.



23. REMOVE OIL PAN SUB-ASSEMBLY


    A099220E02
  1. Remove the 16 bolts and 2 nuts.



    G036411E01
  1. Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surface of the cylinder block and oil pan.



    G037271E01
  1. Remove the O-ring.



24. REMOVE CRANKSHAFT POSITION SENSOR


    A099147E04
  1. Disconnect the sensor connector.

  1. Disconnect the connector from the connector bracket.

  1. Detach the harness clamp.

  1. Remove the bolt and sensor.



25. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    G036504E01
  1. Remove the 19 bolts and 2 nuts shown in the illustration.



    G037273E01
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

    HINT:
    Tape the screwdriver tip before use.



    G037274E01
  1. Remove the 3 O-rings.



    G036021E02
  1. Using a 10 mm socket hexagon wrench, remove the timing gear case plug.



26. REMOVE ENGINE WATER PUMP ASSEMBLY


    A087223E03
  1. Remove the 8 bolts, engine water pump and gasket.