OIL PUMP > REMOVAL |
| 1. REMOVE ENGINE ASSEMBLY |
| 2. INSTALL ENGINE TO ENGINE STAND |
Install the engine to an engine stand with bolts.
| 3. REMOVE IGNITION COIL ASSEMBLY |
![]() |
Disconnect the 4 ignition coil connectors.
Remove the 4 bolts and pull out the 4 ignition coils.
| 4. REMOVE SPARK PLUG |
Using a 16 mm plug wrench, remove the 4 spark plugs.
| 5. REMOVE PCV PIPE |
Remove the bolt and PCV pipe.
| 6. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY |
Disconnect the throttle position sensor and control motor connector.
Disconnect the 2 water by-pass hoses.
![]() |
Remove the 2 bolts, 2 nuts and throttle body with motor.
Remove the gasket from the intake manifold.
| 7. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() |
Disconnect the 4 clamps and wire harness from the delivery pipe.
Disconnect the vacuum hose.
![]() |
Disconnect the 4 injector connectors.
Remove the 2 bolts and fuel delivery pipe together with the fuel injectors.
Remove the 2 No. 1 delivery pipe spacers.
Remove the 4 injector vibration insulators.
![]() |
Using 2 screwdrivers, pry out the 4 spacers from the cylinder head.
Remove the 4 O-rings.
| 8. REMOVE FUEL INJECTOR ASSEMBLY |
![]() |
Pull out the 4 fuel injectors from the delivery pipe.
Remove the 4 O-rings from the 4 fuel injectors.
| 9. REMOVE INTAKE MANIFOLD |
![]() |
Disconnect the vacuum hose and fuel hose.
Disconnect the purge line hose and purge VSV connector.
Remove the 5 bolts, 2 nuts, intake manifold and gasket.
| 10. REMOVE GENERATOR ASSEMBLY |
Detach the terminal cap.
![]() |
Remove the nut, bolt and disconnect the generator wire.
Disconnect the generator connector.
Remove the 2 bolts and generator.
| 11. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET |
![]() |
Remove the 5 bolts and No. 1 compressor mounting bracket.
| 12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 3 bolts and tensioner.
| 13. REMOVE WATER INLET |
![]() |
Disconnect the power steering pump connector.
![]() |
Remove the 2 nuts, bolt and water inlet.
Remove the gasket from the timing chain cover.
| 14. REMOVE THERMOSTAT |
Remove the thermostat from the timing chain cover.
Remove the gasket from the thermostat.
| 15. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt, pulley and spacer.
| 16. REMOVE NO. 1 WATER BY-PASS PIPE |
![]() |
Remove the 2 nuts, water by-pass pipe and gasket.
| 17. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
Remove the oil filler cap from the head cover.
| 18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 19 bolts, 2 nuts, cover and 2 gaskets.
| 19. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Disconnect the sensor connector.
Remove the bolt and sensor.
| 20. REMOVE CRANKSHAFT PULLEY |
![]() |
Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.
Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the No. 1 bearing cap, as shown in the illustration.
![]() |
Using SST, loosen the pulley bolt.
![]() |
Using SST, remove the pulley bolt and pulley.
| 21. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
Remove the drain plug and gasket.
![]() |
Remove the 20 bolts and 2 nuts.
![]() |
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan.
| 22. REMOVE OIL STRAINER SUB-ASSEMBLY |
Remove the bolt, 2 nuts, oil strainer and gasket.
| 23. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
![]() |
Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
![]() |
Remove the O-ring.
| 24. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Disconnect the sensor connector.
Disconnect the connector from the connector bracket.
Detach the harness clamp.
Remove the bolt and sensor.
| 25. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 19 bolts and 2 nuts shown in the illustration.
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
![]() |
Remove the 3 O-rings.
![]() |
Using a 10 mm socket hexagon wrench, remove the timing gear case plug.
| 26. REMOVE ENGINE WATER PUMP ASSEMBLY |
![]() |
Remove the 8 bolts, engine water pump and gasket.