Home › ENGINE ยท 2TR-FBE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > INSPECTION

for Preparation Click here



1. INSPECT OIL NOZZLE
  1. Check the oil nozzles for damage or clogging.
    If necessary, replace the oil nozzle.



2. INSPECT CHAIN


    A097900E03
  1. Pull the chain with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.

  1. Using a vernier caliper, measure the length of 16 links.

    Maximum chain elongation:
    147.5 mm (5.81 in.)

    If the elongation is more than the maximum, replace the chain.

    NOTICE:
    Make the same measurement pulling at 3 or more places selected at random. Average the measurements.



3. INSPECT NO. 2 CHAIN


    A097900E03
  1. Pull the chain with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.

  1. Using a vernier caliper, measure the length of 16 links.

    Maximum chain elongation:
    123.6 mm (4.87 in.)

    If the elongation is more than the maximum, replace the chain.

    NOTICE:
    Make the same measurement pulling at 3 or more places selected at random. Average the measurements.



4. INSPECT CAMSHAFT TIMING GEAR


    A062190E02
  1. Check the lock of the camshaft timing gear.

    1. Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.

      NOTICE:
      Be careful not to damage the camshaft.



  1. Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      2 advance side paths are provided in the groove of the camshaft. Plug one of the paths with a rubber piece.

    2. Break through the tape of the advance side path and the retard side path on the opposite side of the groove.



    3. A062191E03
    4. Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the paths whose tape was broken in the procedure above.

      CAUTION:
      Some oil spraying will occur. Contain the spray with a shop rag.



    5. A062192E13
    6. Check that the camshaft timing gear revolves in the advance direction when weakening the air pressure of the retard side path.

      OK:
      Gear rotates in advance direction.

      HINT:
      This operation releases the lock pin for the extreme retard position.

    7. When the camshaft timing gear reaches the extreme advance position, remove the air gun from the retard side path and advance side path, in that order.

      NOTICE:
      Do not remove the air gun from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Rotate the camshaft timing gear within its movable range several times, but do not turn it to the extreme retard position. Check that the gear rotates smoothly.

      OK:
      Gear rotates in advance direction.

      NOTICE:
      Do not use an air gun to perform the smooth operation check.

  1. Check the lock in the extreme retard position.

    1. Confirm that the camshaft timing gear is locked at the extreme retard position.



5. INSPECT NO. 1 CAMSHAFT
  1. Check the camshaft for runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.00118 in.)

      If the circle runout is more than the maximum, replace the camshaft.

  1. Using a micrometer, measure the cam lobe height.

    Standard cam lobe height:
    42.855 to 42.955 mm (1.687 to 1.691 in.)

    Minimum cam lobe height:
    42.855 mm (1.687 in.)

    If the cam lobe height is less than the minimum, replace the camshaft.

  1. Using a micrometer, measure the journal diameter.

    Standard journal diameter:
    Item
    Specified Condition
    No. 1 journal
    35.949 to 35.965 mm (1.415 to 1.416 in.)
    Other journal
    26.959 to 26.975 mm (1.061 to 1.062 in.)

    If the journal diameter is not as specified, check the oil clearance.



6. INSPECT NO. 2 CAMSHAFT
  1. Check the camshaft for runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.00118 in.)

      If the circle runout is more than the maximum, replace the camshaft.

  1. Using a micrometer, measure the cam lobe height.

    Standard cam lobe height:
    42.854 to 42.954 mm (1.687 to 1.691 in.)

    Minimum cam lobe height:
    42.854 mm (1.687 in.)

    If the cam lobe height is less than the minimum, replace the camshaft.

  1. Using a micrometer, measure the journal diameter.

    Standard journal diameter:
    Item
    Specified Condition
    No. 1 journal
    35.949 to 35.965 mm (1.415 to 1.416 in.)
    Other journal
    26.959 to 26.975 mm (1.061 to 1.062 in.)

    If the journal diameter is not as specified, check the oil clearance.



7. INSPECT NO. 1 CHAIN TENSIONER


    A097905E03
  1. Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.



8. INSPECT NO. 2 CHAIN TENSIONER


    G037464E02
  1. Move the stopper plate downward to release the lock.
    Push the plunger and check that it moves smoothly.



9. INSPECT CAMSHAFT TIMING SPROCKET


    A097906E05
  1. Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.0394 in.)

    If the distance is less than the minimum, replace the sprocket.

    HINT:
    If the worn area is too small or difficult to distinguish from a normal area, perform the steps below.

  1. Wrap the chain around the sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    113.8 mm (4.48 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.



10. INSPECT CAMSHAFT TIMING GEAR


    A097907E06
  1. Measure the distance between the most worn out timing gear tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.0394 in.)

    If the distance is less than the minimum, replace the timing gear.

    HINT:
    If the worn area is too small or difficult to distinguish from a normal area, perform the steps below.

  1. Wrap the chain around the timing gear.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    113.8 mm (4.48 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and timing gear.



11. INSPECT CRANKSHAFT TIMING SPROCKET


    A097908E05
  1. Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.0394 in.)

    If the distance is less than the minimum, replace the sprocket.

    HINT:
    If the worn area is too small or difficult to distinguish from a normal area, perform the steps below.

  1. Wrap the chain around the drive sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    59.4 mm (2.34 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.



12. INSPECT CHAIN TENSIONER SLIPPER


    A097909E07
  1. Using a vernier caliper, measure the tensioner slipper wear.

    Maximum wear:
    2.0 mm (0.0787 in.)

    If the wear is more than the maximum, replace the tensioner slipper.



13. INSPECT CHAIN VIBRATION DAMPER


    A097910E07
  1. Using a vernier caliper, measure the vibration damper wear.

    Maximum wear:
    2.0 mm (0.0787 in.)

    If the wear is more than the maximum, replace the vibration damper.



14. INSPECT TIMING CHAIN GUIDE


    A097911E07
  1. Using a vernier caliper, measure the chain guide wear.

    Maximum wear:
    0.5 mm (0.0197 in.)

    If the wear is more than the maximum, replace the timing chain guide.



15. INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET


    G038149E01
  1. Wrap the chain around the sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    96.7 mm (3.81 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.



16. INSPECT BALANCE SHAFT DRIVE GEAR


    G038148E01
  1. Wrap the chain around the sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    75.9 mm (2.99 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.



17. INSPECT NO. 2 CHAIN VIBRATION DAMPER


    G037311E02
  1. Using a vernier caliper, measure the No. 2 vibration damper wear.

    Maximum wear:
    1.0 mm (0.0391 in.)

    If the wear is more than the maximum, replace the vibration damper.



18. INSPECT NO. 3 CHAIN VIBRATION DAMPER


    A068741E02
  1. Using a vernier caliper, measure the No. 3 vibration damper wear.

    Maximum wear:
    1.0 mm (0.0391 in.)

    If the wear is more than the maximum, replace the vibration damper.



19. INSPECT NO. 4 CHAIN VIBRATION DAMPER


    A068742E02
  1. Using a vernier caliper, measure the No. 4 vibration damper wear.

    Maximum wear:
    1.0 mm (0.0391 in.)

    If the wear is more than the maximum, replace the vibration damper.



20. INSPECT CYLINDER HEAD SET BOLT


    G035889E10
  1. Using a vernier caliper, measure the minimum diameter of the elongated thread at the measuring point.

    Standard outside diameter:
    10.76 to 10.97 mm (0.424 to 0.432 in.)

    Minimum outside diameter:
    10.40 mm (0.409 in.)

    HINT:
    If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the lowest diameter.

    If the diameter is less than the minimum, replace the cylinder head bolt.



21. INSPECT VALVE LASH ADJUSTER


A097867E01

NOTICE:
  1. Keep the lash adjuster free from foreign matter.
  2. Only use clean engine oil.

  1. Place the lash adjuster into a container full of engine oil.

  1. Insert SST's tip into the lash adjuster's plunger and use the tip to press down on the checkball inside the plunger.

    SST
    09276-75010  

  1. Squeeze the SST and lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of the SST is actually pressing the checkball as shown in the illustration. If the checkball is not pressed, air will not bleed.

  1. After bleeding air, remove SST. Then, try to quickly and firmly press the plunger with a finger.

    OK:
    Plunger is difficult to move.

    If the result is not as specified, replace the lash adjuster.



22. INSPECT CYLINDER HEAD FOR FLATNESS


    A097935E05
  1. Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder block and manifold for warpage.

    Maximum warpage:
    0.05 mm (0.00197 in.)

    If the warpage is more than the maximum, replace the cylinder head.



23. INSPECT CYLINDER HEAD FOR CRACKS


    A086993E01
  1. Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
    If cracked, replace the cylinder head.



24. INSPECT INTAKE VALVE SEAT


    A099448E01
  1. Apply a light coat of Prussian blue (or white lead) to the valve face.

  1. Lightly press the valve face against the valve seat.

  1. Check the valve face and valve seat according to the following procedures.

    1. If blue appears 360° around the valve face, the valve face is concentric. If not, replace the valve.

    2. If blue appears 360° around the valve seat, the guide and valve face are concentric. If not, resurface the valve seat.

    3. Check that the valve seat contact is in the middle of the valve face with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).



25. INSPECT EXHAUST VALVE SEAT


    A099449E01
  1. Apply a light coat of Prussian blue (or white lead) to the valve face.

  1. Lightly press the valve face against the valve seat.

  1. Check the valve face and valve seat according to the following procedures.

    1. If blue appears 360° around the valve face, the valve face is concentric. If not, replace the valve.

    2. If blue appears 360° around the valve seat, the guide and valve face are concentric. If not, resurface the valve seat.

    3. Check that the valve seat contact is in the middle of the valve face with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).



26. INSPECT CAMSHAFT THRUST CLEARANCE


    A086998E01
  1. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard thrust clearance:
    0.10 to 0.24 mm (0.00394 to 0.00945 in.)

    Maximum thrust clearance:
    0.26 mm (0.0102 in.)

    If the thrust clearance is more than the maximum, replace the cylinder head. If the thrust surface is damaged, replace the camshaft.



27. INSPECT CAMSHAFT OIL CLEARANCE


    A086999E02
  1. Clean the bearing caps and camshaft journals.

  1. Place the camshafts on the cylinder head.

  1. Lay a strip of Plastigage across each of the camshaft journals.

  1. Install the bearing caps .

    NOTICE:
    Do not turn the camshaft.

  1. Remove the bearing caps.



    A087000E01
  1. Measure the Plastigage at its widest point.

    Standard oil clearance:
    Item
    Specified Condition
    No. 1 journal
    0.035 to 0.072 mm
    (0.00138 to 0.00283 in.)
    Other journal
    0.025 to 0.062 mm
    (0.000984 to 0.00244 in.)

    Maximum oil clearance:
    0.08 mm (0.00315 in.)

    If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head.

  1. Completely remove the Plastigage.



28. INSPECT COMPRESSION SPRING


    A051437E01
  1. Using a vernier caliper, measure the free length of the inner compression spring.

    Standard free length:
    48.53 mm (1.91 in.)

    If the free length is not as specified, replace the spring.



    A062784E01
  1. Using a steel square, measure the deviation of the inner compression spring.

    Maximum deviation:
    1.5 mm (0.0591 in.)

    Maximum angle (reference):
    2°

    If the deviation is more than the maximum, replace the spring.



29. INSPECT INTAKE VALVE
  1. Using a vernier caliper, measure the valve's overall length.

    Standard overall length:
    106.26 mm (4.18 in.)

    Minimum overall length:
    105.96 mm (4.17 in.)

    If the overall length is less than the minimum, replace the valve.

  1. Using a micrometer, measure the diameter of the valve stem.

    Standard valve stem diameter:
    5.470 to 5.485 mm (0.215 to 0.216 in.)



    A099452E01
  1. Using a vernier caliper, measure the valve head margin thickness.

    Standard margin thickness:
    1.05 to 1.45 mm (0.0413 to 0.0571 in.)

    Minimum margin thickness:
    0.50 mm (0.0197 in.)

    If the margin thickness is less than the minimum, replace the valve.



30. INSPECT EXHAUST VALVE
  1. Using a vernier caliper, measure the valve's overall length.

    Standard overall length:
    106.74 mm (4.20 in.)

    Minimum overall length:
    106.44 mm (4.19 in.)

    If the overall length is less than the minimum, replace the valve.

  1. Using a micrometer, measure the diameter of the valve stem.

    Standard valve stem diameter:
    5.465 to 5.480 mm (0.215 to 0.216 in.)



    A099453E01
  1. Using a vernier caliper, measure the valve head margin thickness.

    Standard margin thickness:
    1.2 to 1.6 mm (0.0472 to 0.0630 in.)

    Minimum margin thickness:
    0.50 mm (0.0197 in.)

    If the margin thickness is less than the minimum, replace the valve.



31. INSPECT INTAKE VALVE GUIDE BUSH


    A087005E01
  1. Using a caliper gauge, measure the inside diameter of the guide bush.

    Bush inside diameter:
    5.510 to 5.530 mm (0.217 to 0.218 in.)

  1. Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

    Standard oil clearance:
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)

    Maximum oil clearance:
    0.08 mm (0.00315 in.)

    If the clearance is more than the maximum, replace the valve and guide bush.



32. INSPECT EXHAUST VALVE GUIDE BUSH


    G035204E01
  1. Using a caliper gauge, measure the inside diameter of the guide bush.

    Standard bush inside diameter:
    5.510 to 5.530 mm (0.217 to 0.218 in.)

  1. Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

    Standard oil clearance:
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)

    Maximum oil clearance:
    0.10 mm (0.00394 in.)

    If the clearance is more than the maximum, replace the valve and guide bush.



33. INSPECT NO. 1 BALANCE SHAFT


    G037395E04
  1. Inspect the diameter of the journal.

    1. Using a micrometer, measure the diameter of the balance shaft main journals.

      Standard main journal diameter:
      Item
      Specified Condition
      A
      37.969 to 37.985 mm (1.49 to 1.50 in.)
      B
      37.449 to 37.465 mm (1.474 to 1.475 in.)



    G037397E03
  1. Inspect the diameter of bearing.

    1. Using a cylinder gauge, measure the inside diameter of the balance shaft bearings.

      Standard bearing inside diameter:
      Item
      Specified Condition
      A
      38.025 to 38.045 mm (1.497 to 1.498 in.)
      B
      37.525 to 37.545 mm (1.477 to 1.478 in.)

  1. Inspect the oil clearance.

    1. Subtract the balance shaft main journal diameter measurement from the balance shaft bearing inside diameter measurement.

      Standard oil clearance:
      Item
      Specified Condition
      A
      0.040 to 0.076 mm (0.00157 to 0.00299 in.)
      B
      0.060 to 0.096 mm (0.00236 to 0.00378 in.)

      Maximum oil clearance:
      0.15 mm (0.00591 in.)

      If the oil clearance is more than the maximum, replace the cylinder block and balance shaft.



34. INSPECT NO. 2 BALANCE SHAFT


    G037396E03
  1. Inspect the diameter of the journal.

    1. Using a micrometer, measure the diameter of the balance shaft main journals.

      Standard main journal diameter:
      Item
      Specified Condition
      A
      37.969 to 37.985 mm (1.49 to 1.50 in.)
      B
      37.449 to 37.465 mm (1.474 to 1.475 in.)



    G037398E03
  1. Inspect the diameter of the bearing.

    1. Using a cylinder gauge, measure the inside diameter of the balance shaft bearings.

      Standard bearing inside diameter:
      Item
      Specified Condition
      A
      38.025 to 38.045 mm (1.497 to 1.498 in.)
      B
      37.525 to 37.545 mm (1.477 to 1.478 in.)

  1. Inspect the oil clearance.

    1. Subtract the balance shaft main journal diameter measurement from the balance shaft bearing inside diameter measurement.

      Standard oil clearance:
      Item
      Specified Condition
      A
      0.040 to 0.076 mm (0.00157 to 0.00299 in.)
      B
      0.060 to 0.096 mm (0.00236 to 0.00378 in.)

      Maximum oil clearance:
      0.15 mm (0.00591 in.)

      If the oil clearance is more than the maximum, replace the cylinder block and balance shaft.



35. INSPECT CYLINDER BLOCK


    G037356E01
  1. Inspect for flatness.

    1. Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head gasket for warpage.

      Maximum warpage:
      0.05 mm (0.00197 in.)

      If the warpage is more than the maximum, replace the cylinder block.



    G035190E01
  1. Visually check the cylinder for vertical scratches.
    If deep scratches are present, rebore all the 4 cylinders. If necessary, replace the cylinder block.



    G037358E05
  1. Inspect the cylinder bore diameter.

    1. Using a cylinder gauge, measure the cylinder bore diameter at position A in the thrust and axial directions.

      Standard diameter:
      94.990 to 95.003 mm (3.7398 to 3.7403 in.)

      If the diameter is more than the maximum, rebore all the 4 cylinders. If necessary, replace the cylinder block.



    G035191E04
  1. Inspect the cylinder ridge.

    1. If the wear is less than 0.2 mm (0.00787 in.), using a ridge reamer, grind the top of the cylinder.



36. INSPECT PISTON WITH PIN


    A097953E04
  1. Inspect the piston oil clearance.

    1. Using a micrometer, measure the piston diameter at right angles to the piston center line, the indicated distance from the piston end.

      Standard distance:
      13.8 mm (0.543 in.)

      Standard piston diameter:
      Item
      Specified Condition
      Standard side
      94.940 to 94.966 mm (3.7378 to 3.7384 in.)
      O/S 0.50
      95.440 to 95.466 mm (3.7575 to 3.7585 in.)

    2. Measure the cylinder bore diameter in the thrust directions.

    3. Subtract the piston diameter measurement from the cylinder bore diameter measurement.

      Standard oil clearance:
      0.024 to 0.063 mm (0.000945 to 0.00248 in.)

      If the oil clearance is more than the standard, replace all the 4 pistons and rebore all the 4 cylinders. If necessary, replace the cylinder block.



    A239763
  1. Inspect the piston pin fit.

    1. At 60°C (140°F), check that the piston pin can be pushed into the piston pin hole with your thumb.



37. INSPECT PISTON RING SET


    A239765
  1. Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

    Standard ring groove clearance:
    Item
    Specified Condition
    No. 1 ring
    0.020 to 0.070 mm (0.000787 to 0.00276 in.)
    No. 2 ring
    0.020 to 0.060 mm (0.000787 to 0.00236 in.)
    Oil ring
    0.020 to 0.060 mm (0.000787 to 0.00236 in.)

    If the clearance is not as specified, replace the piston.



    A097954E01
  1. Inspect the piston ring end gap.

    1. Insert the piston ring into the cylinder bore.

    2. Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.



    3. A050189E01
    4. Using a feeler gauge, measure the end gap.

      Standard end gap:
      Item
      Specified Condition
      No. 1 ring
      0.26 to 0.31 mm (0.0102 to 0.0122 in.)
      No. 2 ring
      0.59 to 0.71 mm (0.0232 to 0.0280 in.)
      Oil ring
      0.10 to 0.30 mm (0.00394 to 0.0118 in.)

      Maximum end gap:
      Item
      Specified Condition
      No. 1 ring
      0.90 mm (0.0354 in.)
      No. 2 ring
      1.36 mm (0.0535 in.)
      Oil ring
      0.75 mm (0.0295 in.)

      If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum, even with a new piston ring, rebore all the 4 cylinders or replace the cylinder block.



38. INSPECT CONNECTING ROD


    A054727E01
  1. Using a rod aligner and feeler gauge, check the connecting rod alignment.

    1. Check for bend.

      Maximum bend:
      0.03 mm (0.00118 in.) per 100 mm (3.94 in.)

      If the bend is more than the maximum, replace the connecting rod.



    2. A054728E01
    3. Check for twist.

      Maximum twist:
      0.15 mm (0.00591 in.) per 100 mm (3.94 in.)

      If the twist is more than the maximum, replace the connecting rod.



39. INSPECT PISTON PIN OIL CLEARANCE

HINT:
There is only 1 type of supply part for piston with pin.



    A258022E02
  1. Using a caliper gauge, measure the inside diameter of the piston pin hole.

    Standard Piston Pin Hole Inside Diameter:
    Item
    Specified Condition
    A
    22.001 to 22.004 mm (0.86618 to 0.86630 in.)
    B
    22.005 to 22.007 mm (0.86634 to 0.86642 in.)
    C
    22.008 to 22.010 mm (0.86645 to 0.86653 in.)

    If the diameter is not as specified, replace the piston with pin.



    A258023E02
  1. Using a micrometer, measure the piston pin diameter.

    Measurement Position:
    Measurement Position
    Piston Pin Position
    a
    28 mm (1.10 in.)
    b
    5 mm (0.197 in.)

    Standard Piston Pin Diameter:
    Item
    Specified Condition
    A
    21.997 to 22.000 mm (0.86602 to 0.86614 in.)
    B
    22.001 to 22.003 mm (0.86618 to 0.86626 in.)
    C
    22.004 to 22.006 mm (0.86630 to 0.86638 in.)

    If the diameter is not as specified, replace the piston with pin.

  1. Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.

    Standard oil clearance:
    0.001 to 0.007 mm (0.0000394 to 0.000276 in.)

    Maximum oil clearance:
    0.010 mm (0.000394 in.)

    If the oil clearance is more than the maximum, replace the piston and piston pin as a set.



    G035892E07
  1. Using a caliper gauge, measure the inside diameter of the connecting rod bush.

    Standard Bush Inside Diameter:
    Item
    Specified Condition
    A
    22.005 to 22.008 mm (0.86634 to 0.86645 in.)
    B
    22.009 to 22.011 mm (0.86649 to 0.86657 in.)
    C
    22.012 to 22.014 mm (0.86661 to 0.86669 in.)

    If the diameter is not as specified, replace the connecting rod small end bush.

  1. Subtract the piston pin diameter measurement from the bush inside diameter measurement.

    Standard oil clearance:
    0.005 to 0.011 mm (0.000197 to 0.000433 in.)

    Maximum oil clearance:
    0.025 mm (0.000984 in.)

    If the oil clearance is more than the maximum, replace the connecting rod small end bush. If necessary, replace the connecting rod and piston pin as a set.



40. INSPECT CONNECTING ROD BOLT


    A054729E03
  1. Using a vernier caliper, measure the tension portion diameter of the bolt.

    Standard diameter:
    7.2 to 7.3 mm (0.283 to 0.287 in.)

    Minimum diameter:
    7.0 mm (0.276 in.)

    If the diameter is less than the minimum, replace the bolt.



41. INSPECT CRANKSHAFT


    A013859E01
  1. Inspect for circle runout.

    1. Place the crankshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.00118 in.)

      If the circle runout is more than the maximum, replace the crankshaft.



    G037369E04
  1. Inspect the main journals.

    1. Using a micrometer, measure the diameter of each main journal.

      Standard journal diameter:
      Item
      Specified Condition
      No. 3 journal
      59.981 to 59.994 mm (2.361 to 2.362 in.)
      Except No. 3 journal
      59.987 to 60.000 mm (2.3617 to 2.3622 in.)

      If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.

    2. Check each main journal for taper and out-of-round as shown in the illustration.

      Maximum taper and out-of-round:
      0.005 mm (0.000197 in.)

      If the taper and out-of-round is more than the maximum, replace the crankshaft.



    G037370E01
  1. Inspect the crank pin.

    1. Using a micrometer, measure the diameter of each crank pin.

      Diameter:
      52.989 to 53.002 mm (2.086 to 2.087 in.)

      If the diameter is not as specified, check the oil clearance (see "INSPECT CONNECTING ROD OIL CLEARANCE" procedures). If necessary, replace the crankshaft.

    2. Check each crank pin for taper and out-of-round as shown in the illustration.

      Maximum taper and out-of-round:
      0.003 mm (0.000118 in.)

      If the taper and out-of-round is more than the maximum, replace the crankshaft.



42. INSPECT CRANKSHAFT BEARING CAP SET BOLT


    G035889E11
  1. Using a vernier caliper, measure the minimum diameter of the elongated thread at the measuring point.

    Standard outside diameter:
    10.76 to 10.97 mm (0.424 to 0.432 in.)

    Minimum outside diameter:
    10.66 mm (0.420 in.)

    If the diameter is less than the minimum, replace the crankshaft bearing cap bolt.